mypros+
Model reference

GE ZET958

Oven

9 documents10 error codes15 service modes

Available documentation

Service Manual

  • Owner's Manual - 27″ and 30″ Convection Wall Oven48 pg
    Covers this model
  • Owner's Manual 27″ and 30″ Convection Wall Oven48 pg
    Covers this model

Tech Sheet

  • Appliance Diagnostic Modes Range GE Consumer & Industrial Technical Training255 pg
    Covers this model

Bulletin

  • Service Bulletin RANGE RA 04-041 pg
    Covers this model
  • Calibration Error and F0 Display1 pg
    Covers this model
  • Service Bulletin - Calibration Error and F0 Display1 pg
    Covers this model

Training

  • GE and Monogram 27-In. and 30-In. Wall Ovens Technical Service Guide51 pg
    Covers this model

Installation Guide

  • Installation Instructions - 30" Built-In Wall Oven16 pg
    Covers this model
  • Built-In Wall Oven Installation Instructions40 pg
    Covers this model
MyPros+ Max

Diagnose your GE ZET958.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (10)

CodeMeaning
FFunction error code indicated by 'F' followed by a number or letter flashing in…F0Stuck key or shorted keypad detected on the control panel.F2Oven over-temperature condition detected by the control.F3Oven temperature sensor open circuit (open sensor).F4Oven temperature sensor shorted circuit (shorted sensor).F5Sensor circuit supervisor failure in the control board.F7Stuck or shorted function key on the keypad.F8Control board failure (internal ERC fault).F9Door lock/latch motor failureFFLoss of latch motor safety circuit.

Service modes (15)

  • Control Lockout["Press the 9 and 0 pads at the same time for 3 seconds until the display shows 'LOC ON'."]
  • Glass Touch Parameter Setting (Control Not Replaced)1
  • Glass Touch Parameter Setting (New Part Installation)1
  • J2S968/JGS968/JGSP48 Fault Code Recall["Press TIMER, CLOCK, and MIN DOWN (or 9) key to get Fault Codes to appear."]
  • JB905/968/988 Fault Code Recall["Press TIMER and CLOCK (or 9) key to get Fault Codes to appear."]
  • JP938/JP968 Cooktop Calibration Mode["Clear everything from the top of the glass.","Lock the control by pressing the LOCK key for 3…
  • JP938/JP968 Cooktop Technician Mode["Lock cooktop by holding CONTROL LOCK key for 3 seconds.","Control will beep 2 times and LOCK…
  • LOC REF Procedure (JCK915/JCT915/JK915/JT915/JK955/JT955/ZEK938/ZET958)["Reinitiate LOC REF procedure by pressing BAKE/BROIL simultaneously.","For digital keypads press 9…
  • Oven Calibration1. Press and hold Bake & Broil pads until SF appears in display. 2. Press Bake pad to enter oven…
  • Oven Thermostat Adjustment["Press the BAKE and BROIL HIGH/LOW pads at the same time for 3 seconds until the display shows…
  • Recall Stored F-codesPress TIMER, CLOCK, and MIN DOWN (or 9) simultaneously.
  • Sales ModePress Clock and Timer pads at the same time.
  • Special Features (SF) Mode["Press the BAKE and BROIL HIGH/LOW pads at the same time for 3 seconds until the display shows…
  • Special Functions (SF) ModePress and hold BAKE and BROIL pads simultaneously for 2 seconds until SF appears in display.
  • Trivection Service Mode["Disconnect main power to the oven for at least 15 seconds.","Reconnect power and enter 0803 on…

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass