mypros+
Model reference

GE JGS968

Range

10 documents11 error codes19 service modes

Available documentation

Service Manual

  • Owner's Manual - Gas Slide-In Ranges100 pg
    Covers this model
  • TECHNICAL SERVICE GUIDE Profile Dual Fuel and Profile All Gas Slide-In Ranges63 pg
    Covers this model
  • Gas Slide-In Ranges Owner's Manual96 pg
    Covers this model
  • Profile Dual Fuel and Profile All Gas Slide-In Ranges Technical Service Guide63 pg
    Covers this model

Tech Sheet

  • Appliance Diagnostic Modes Range GE Consumer & Industrial Technical Training255 pg
    Covers this model

Bulletin

  • Service Bulletin - Delayed Oven Ignition Problem1 pg
    Covers this model
  • Service Bulletin RANGE RA 04-041 pg
    Covers this model
  • Calibration Error and F0 Display1 pg
    Covers this model
  • Service Bulletin - Calibration Error and F0 Display1 pg
    Covers this model

Other

  • 31 144504 pg
    Covers this model
MyPros+ Max

Diagnose your GE JGS968.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (11)

CodeMeaning
FFunction error code indicated by 'F' followed by a number or letter flashing in…F-Function error code indicated by F- followed by a number or letter flashing in…F0Shorted OFF key detected on the control panel.F2Over temperature conditionF3Open oven sensor (under 950 ohms).F4Shorted oven sensor (over 2900 ohms).F5Sensor circuit supervisor failure in the control board.F7Shorted matrix or START key.F8EEPROM data shift failure.F9Cooling fan stalls while above 650°F; open thermal switch in yellow leads.FFLoss of latch motor safety circuit.

Service modes (19)

  • 12-Hour Shutdown Disable1
  • 12-Hour, 24-Hour, or Clock Blackout1
  • Auto Recipe Conversion (Convection)1
  • Control LockoutTouch and hold the 9 and 0 pads at the same time for 3 seconds.
  • F Code RecallPress TIMER, CLOCK, MIN DOWN (or 9) together to recall stored F codes.
  • Fahrenheit or Celsius Temperature Selection1
  • Failure Code RecallPress TIMER, CLOCK, and MIN DOWN (or 9) together to recall stored F codes.
  • J2S968/JGS968/JGSP48 Fault Code Recall["Press TIMER, CLOCK, and MIN DOWN (or 9) key to get Fault Codes to appear."]
  • JB905/968/988 Fault Code Recall["Press TIMER and CLOCK (or 9) key to get Fault Codes to appear."]
  • JP938/JP968 Cooktop Calibration Mode["Clear everything from the top of the glass.","Lock the control by pressing the LOCK key for 3…
  • JP938/JP968 Cooktop Technician Mode["Lock cooktop by holding CONTROL LOCK key for 3 seconds.","Control will beep 2 times and LOCK…
  • LOC REF Procedure (JCK915/JCT915/JK915/JT915/JK955/JT955/ZEK938/ZET958)["Reinitiate LOC REF procedure by pressing BAKE/BROIL simultaneously.","For digital keypads press 9…
  • Oven Calibration Mode1
  • Sabbath Feature1
  • Special Features Mode (SF)Touch the BROIL HI/LO and BAKE pads at the same time for 3 seconds until the display shows SF.
  • Thermostat Adjustment1
  • Tone Volume Adjustment1. Touch the BROIL HI/LO and BAKE pads at the same time for 3 seconds until the display shows 'SF'…
  • Tones at End of Timed Cycle (Cancel 6-second beep)1
  • Trivection Service Mode["Disconnect main power to the oven for at least 15 seconds.","Reconnect power and enter 0803 on…

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass