Model reference
Kenmore 66512773K310
Dishwasher
7 documents52 error codes5 service modes
Available documentation
Service Manual
- Technical Reference Manual - Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
- Kenmore Elite 2013 Stainless Steel Tall Tub Dishwashers82 pg
Tech Sheet
- Kenmore Dishwasher 66515769000 Technical Sheet2 pg
Service Flash
- Service Information Kenmore Dishwasher11 pg
- Repair Tip RT22-316 - Kenmore Dishwasher Lower Rack Hard to Move in and Out of Tub1 pg
Other
- Use & Care Guide - Kenmore Dishwasher18 pg
- technicalreferencemanual 2211031382 pg
MyPros+ Max
Diagnose your Kenmore 66512773K310.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (52)
CodeMeaning
1-1Control detected K400 pilot relay stuck closed.1-2Damaged or corrupted memory on control board; incompatible software components…10-1Dispenser electrical problem; loose connection in dispenser circuit and/or open…10-2Vent wax motor electrical problem; loose connection in vent circuit and/or open…10-3Drying fan error; loose connection in fan circuit and/or open fan motor; faulty…2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control; loose user interface…3-1Open connection or component in temperature sensing circuit; open or faulty…3-2Shorted connection or component in temperature sensing circuit; shorted or…3-3OWI failure; failed calibration.4-4Wash motor failure; loose connection in wash motor circuit and/or open wash…5-1Door stuck open; door was not latched within 3 seconds of pressing…5-2Door stuck closed; control programmed to not start if it suspects door switch…6-1Low/no water (mechanical problem); no water to dishwasher, bowls capturing wash…6-2Fill valve electrical problem; loose connection in fill valve circuit and/or…6-3Suds/air in pump; too many suds, bowls capturing wash water, water leaking…6-4Float switch open; overfill switch stuck in open position and/or dishwasher not…6-6Cool water; incoming water temperature under 18°C/65°F.7-1No heat; control programmed to disable heater if it detects a water heating…7-2Heater stuck on; faulty heater drive circuit on the control.8-1Slow drain; obstructed drain hose or path; drain pump impeller fractured or…8-4Drain motor electrical problem; loose connection in drain motor circuit and/or…9-1Diverter can't find position; corroded or loose connection in diverter…9-2Diverter stuck on; faulty diverter drive circuit on the control.9-3Control detected diverter disk in sump is missing.9-4Lower spray arm error; mechanical binding or blocking of spray arm; corroded or…F10E1Dispenser electrical problem; loose connection in dispenser circuit and/or open…F10E2Vent wax motor electrical problem; loose connection in vent circuit and/or open…F10E3Drying fan error; loose connection in fan circuit and/or open fan motor (on…F1E1Control detected K400 pilot relay stuck closed.View all 52 error codes
F1E2Damaged or corrupted memory on control board; incompatible software components…F2E1Control detected stuck key(s) in keypad or keypad connection.F2E2User interface cannot communicate with main control; loose user interface…F3E1Open connection or component in temperature sensing circuit; open or faulty…F3E2Shorted connection or component in temperature sensing circuit; incoming water…F3E3OWI failed calibration.F4E4Loose connection in wash motor circuit and/or open wash motor; motor fuse on…F5E1Door was not latched within 3 seconds of pressing Start/Resume; loose…F5E2Control suspects door switch is stuck closed; control looks for door switch to…F6E1Low or no water to dishwasher (mechanical problem); multiple potential causes…F6E2Fill valve electrical problem; loose connection in fill valve circuit and/or…F6E3Suds or air in pump; too many suds, captured wash water, water leaking, or…F6E4Overfill (float) switch stuck in open position and/or dishwasher not level…F6E6Incoming water temperature under 18°C/65°F.F7E1No heat; control disabled heater due to detected water heating problem; open…F7E2Heater stuck on; faulty heater drive circuit on the control.F8E1Slow drain; obstructed drain hose or path; drain pump impeller fractured or…F8E4Drain motor electrical problem; loose connection in drain motor circuit and/or…F9E1Diverter can't find position; corroded or loose connection in diverter…F9E2Diverter stuck on; faulty diverter drive circuit on the control.F9E3Diverter disc missing from sump.F9E4Lower spray arm error; mechanical binding or blocking of spray arm; corroded or…
Service modes (5)
- Clear Customer Error HistoryDuring the Service Diagnostic Cycle, press the HI TEMP key during the designated interval (noted in…
- Rapid Advance Mode (during active cycle)After starting a cycle, press HI TEMP
- Rapid Advance Mode (during normal cycle)After starting a cycle, press HI TEMP
- Sales Demo Mode ClearRun Service Diagnostics Cycle to clear demo mode.
- Service Diagnostic CycleWith dishwasher in standby, press any 3 keys in the sequence 1-2-3, 1-2-3, 1-2-3 with no more than…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Kenmore dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax