mypros+
Model reference

KitchenAid KFGC500JIB00

Range

10 documents50 error codes19 service modes

Available documentation

Service Manual

  • Dimension Guide30 pg
    Covers this model
  • Tech Manual39 pg
    Covers this model
  • SERVICE MANUAL - JennAir® and KitchenAid® Dual-Fuel/Gas/Steam Commercial Ranges79 pg
    Covers this model
  • SERVICE MANUAL JENNAIR Dual-Fuel Commercial Ranges67 pg
    Covers this model
  • Technical Manual - W11372006 - Rev B - JennAir and KitchenAid Dual-Fuel and Gas Commercial Ranges86 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W11565467 - Rev A2 pg
    Covers this model

Bulletin

  • Technical Service Pointer #W114482133 pg
    Covers this model

Service Flash

  • Technical Service Pointer3 pg
    Covers this model
  • Technical Service Pointer9 pg
    Covers this model

Installation Guide

  • Installation Instructions40 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KFGC500JIB00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (50)

CodeMeaning
F1 E0Oven user interface failure.F1 E1Internal Oven Appliance Manager (AM) error.F1E0User Interface BoardF1E1Control Relay BoardF2 E0Keypad disconnected.F2 E1Stuck or shorted key on keypad.F2E0Keypad disconnected.F2E1Stuck KeyF2E2Oven KnobF3 E0Main oven temperature sensor open or shorted.F3 E1Bottom oven temperature sensor open or shorted.F3 E3Meat probe connector jack or meat probe shorted.F3E0Main Oven Sensor Open or Shorted.F3E1Main Oven Meat Probe Short-Circuit.F3E3Main Oven Door Latch Switch error.F3E9Left Oven Meat Probe Short-Circuit.F5 E0Door and latch switch do not agree (main/upper oven).F5 E1Latch not operating (main/upper oven).F5 E3Door and latch switch do not agree (lower oven).F5 E4Latch not operating (lower oven).F5E0Main Oven Door Latch Switch error.F5E1Main Oven Door Latch Motor error.F5E3Left Oven Door Latch Switch error.F5E4Left Oven Door Latch Motor error.F6 E0Oven user interface lost communication.F6 E1Over temperature (main/upper oven).F6 E3Over temperature (lower oven).F6 E4User Interface / Appliance Manager state status mismatch.F6 E6Oven appliance manager lost communication (main/upper oven).F6 E9Oven appliance manager lost communication (lower oven).
View all 50 error codes
F6 EAUser Interface over temperature.F6E0User Interface Connection error.F6E1Main Oven Over Temperature Limit exceeded.F6E3Left Oven Over Temperature Limit exceeded.F6E4Control Status error.F6E6Main Oven Control Connection error.F6E9Left Oven Control Connection error.F6EAUser Interface over temperature.F7E1Boiler Over Temperature Limit (steam models)F7E2Boiler Temperature Out of Range (steam models)F8 E0Low fan speed underspeed.F8 E1Low fan speed overspeed.F8 E2High fan speed underspeed.F8 E3High fan speed overspeed.F8E0Main Oven Cooling Fan speed low or not functioning.F8E1Left Oven Cooling Fan Speed Low.F8E2Main Oven Cooling Fan Speed High.F8E3Left Oven Cooling Fan Speed High.F9 E0Product not wired correctly (neutral connection may be switched with L1 or L2).F9E0Power Input

Service modes (19)

  • Cavity Size Select1
  • cavity_size_select1
  • diagnosticPress CANCEL > CANCEL > START on the control panel.
  • Diagnostics modePress CANCEL > CANCEL > START
  • Diagnostics Mode Entry["With the appliance in standby mode, ensure Mode Selector knob is at Bake and Temperature knob is…
  • Error Codes (Fault History)1
  • error_codes_view1
  • Fault Code DisplayWhile in Diagnostics Mode, rotate the Mode Selector knob clockwise until Fault Code Display is…
  • fault_code_display["Enter Diagnostics Mode first.","Rotate Mode Selector knob clockwise until top LEDs are…
  • Manual DiagnosticWhile in Diagnostics Mode, rotate the Mode Selector knob clockwise until Manual Diagnostic is…
  • Manual Diagnostics["Enter Diagnostics Mode.","Rotate the Mode Selector knob clockwise until the Top and Right LEDs…
  • manual_diagnostic["Enter Diagnostics Mode first.","Rotate Mode Selector knob clockwise until top and right LEDs are…
  • Relay Activation1
  • relay_activation1
  • Service Diagnostic Mode Entry1. Start with knobs in initial position
  • Software VersionFor Engineering only
  • Status Screen1
  • status_screen1
  • Suspend Code Status (KitchenAid only)["Turn Mode Knob away from OFF and back to OFF to suspend Error Status (Amber LED) display."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass