mypros+
Model reference

KitchenAid KGRT507FWH1

Range

5 documents61 error codes34 service modes

Available documentation

Tech Sheet

  • TECH SHEET - KitchenAid Range KGST307BBL28 pg
    Covers this model
  • TECH SHEET8 pg
    Covers this model

Service Manual

  • Kitchenaid Electronic Range Controls "B" & D Line Wall Ovens Job Aid93 pg
    Covers this model
  • KitchenAid Electronic Range Controls "B" & "D" Line Wall Ovens Job Aid93 pg
    Covers this model

Other

  • Kitchenaid Range KGST307BBL2 Wiring Sheet 97526681 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KGRT507FWH1.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (61)

CodeMeaning
F1 E0EEPROM read fault (silent fault, not displayed).F1 E1EEPROM checksum does not match at start key (silent fault, not displayed).F1 E3Configuration jumper changeF1 E4Q8 shorted.F1 E9Stack overflow, highest priority fault.F1-E0EEPROM read fault (silent fault, not displayed).F1-E1EEPROM checksum does not match at start key (silent fault, not displayed).F1-E3Configuration jumper changeF1-E4Q8 shorted.F1-E9Stack overflow, highest priority fault.F1E0EEPROM read fault (silent fault, not displayed).F1E1EEPROM checksum does not match at start key (silent fault, not displayed).F1E3Configuration jumper change; freestanding, electric switches or P9 pins 6 to 7…F1E4Q8 shorted.F1E9Stack overflow, highest priority.F2 E0Cancel key level too low (open).F2 E2Cancel key loop test failed.F2 E3Key held down too long or keyboard short.F2 E4Keys unsettled, probably due to noise.F2-E0Cancel key level too low (open).F2-E2Cancel key loop test failed.F2-E3Key held down too long or keyboard short.F2-E4Keys unsettled, probably due to noise.F2E0Cancel key level too low (open).F2E2Cancel key loop test failed.F2E3Key held down too long or keyboard short.F2E4Keys unsettled probably due to noise.F3 E0Oven temperature sensor (PLAT sensor) open.F3 E1Oven temperature sensor (PLAT sensor) shorted.F3 E2Oven temperature too high (runaway).
View all 61 error codes
F3-E0Platinum (PLAT) temperature sensor open.F3-E1Platinum (PLAT) temperature sensor shorted.F3-E2Oven temperature too high (runaway).F3E0Oven sensor open.F3E1Shorted oven sensor.F3E2Oven temp too high (runaway).F4 E1Meat probe shorted (less than 1500 ohms).F4-E1Meat probe shorted (less than 1500 ohms).F4E1Meat probe shorted (less than 1500 ohms).F5 E1Self-clean latch will not make after 30 seconds.F5 E3Loss of 120 VAC across L1 to ground, or Q19 circuit error.F5 E5Self-clean temperature not satisfied after 30 minutes.F5 E6Door locked with door open.F5 E7Door unlocked and will not unlatch.F5-E1Self-clean latch will not make after 30 seconds.F5-E3Loss of 120 VAC across L1 to ground, or Q19 circuit error (L1-N reverse).F5-E5Self-clean temperature not satisfied after 30 minutes.F5-E6Door locked with door open.F5-E7Door unlocked and will not unlatch.F5E1Self clean latch lock make after 30 seconds.F5E3Loss of 120 VAC across L1 to Ground or Q19 circuit error.F5E5Self clean temperature not satisfied after 30 minutes.F5E6Door locked somehow with door open.F5E7Door unlocked somehow and will not unlatch.F6 E0Ambient sensor opened (too hot).F6-E0Ambient sensor opened (too hot).F6E0Ambient (console bi-metal) sensor opened (too hot).F7 E0Input switches will not follow their strobe level (shorted to ground).F7-E0Input switches will not follow their strobe level (shorted to ground).F7E0Input switches won't follow their strobe level (shorted to ground).PFPower failure (not a failure of control).

Service modes (34)

  • Convection Freestanding/Slide-In Board ProgrammingAfter powering up the unit, press the following keypads in sequence
  • Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
  • F1E3 Configuration Reconfiguration ProcedureStep 1: Make sure harness to P1 connector is correct per wiring diagram. Step 2: Power down and…
  • F1E3 Configuration Reset["Verify harness to P1 connector is correct per wiring diagram.","STEP 1
  • Hidden Functions - Bake Temperature CalibrationTouch and hold the Bake keypad for 5 seconds.
  • Hidden Functions - Calibration (Bake keypad)Touch and hold the Bake keypad for 5 seconds.
  • Hidden Functions - Clock Display OffTouch and hold the Clock keypad for 5 seconds.
  • Hidden Functions - Clock Display Off (Clock keypad)Touch and hold the Clock keypad for 5 seconds.
  • Hidden Functions - DehydrateTouch and hold the Conv
  • Hidden Functions - Dehydrate (Conv. Bake keypad)Touch and hold the Conv
  • Hidden Functions - End-of-Cycle Tones OffTouch and hold the Cook Time keypad for 5 seconds.
  • Hidden Functions - End-of-Cycle Tones Off (Cook Time keypad)Touch and hold the Cook Time keypad for 5 seconds.
  • Hidden Functions - Fahrenheit/Celsius ToggleTouch and hold the Broil keypad for 5 seconds.
  • Hidden Functions - Fahrenheit/Celsius Toggle (Broil keypad)Touch and hold the Broil keypad for 5 seconds.
  • Hidden Functions - Keypad Entry Tones OffTouch and hold the Stop Time keypad for 5 seconds.
  • Hidden Functions - Keypad Entry Tones Off (Stop Time keypad)Touch and hold the Stop Time keypad for 5 seconds.
  • Hidden Functions - Keypad LockoutTouch and hold the #3 keypad for 5 seconds.
  • Hidden Functions - Keypad Lockout (3 keypad)Touch and hold the #3 keypad for 5 seconds.
  • Hidden Functions - Last F/E Code and ROM RevisionTouch and hold the #0 keypad for 5 seconds.
  • Hidden Functions - Last F/E Code and ROM Revision (0 keypad)Touch and hold the #0 keypad for 5 seconds.
  • Hidden Functions - Raising Bread (Baked Goods keypad)Touch and hold the Baked Goods keypad for 5 seconds.
  • Hidden Functions - Raising Bread DoughTouch and hold the Baked Goods keypad for 5 seconds.
  • Hidden Functions - Range Configuration DisplayTouch and hold the #1 keypad for 5 seconds.
  • Hidden Functions - Range Configuration Display (1 keypad)Touch and hold the #1 keypad for 5 seconds.
  • Hidden Functions - Sabbath Mode (6 keypad)Touch and hold the #6 keypad for 5 seconds (after oven has finished preheating in Bake mode).
  • Hidden Functions - Sell ModeTouch and hold the Timer Cancel keypad for 5 seconds.
  • Hidden Functions - Sell Mode (Timer Cancel keypad)Touch and hold the Timer Cancel keypad for 5 seconds.
  • Hidden Functions - Timer Operating Tones OffTouch and hold the Timer Start keypad for 5 seconds.
  • Hidden Functions - Timer Operating Tones Off (Timer Start keypad)Touch and hold the Timer Start keypad for 5 seconds.
  • Hidden Functions - Tone Frequency ChangeTouch and hold the #7 keypad for 5 seconds.
  • Hidden Functions - Tone Frequency Change (7 keypad)Touch and hold the #7 keypad for 5 seconds.
  • Non-Convection Freestanding/Slide-In Board ProgrammingAfter powering up the unit, press the following keypads in sequence
  • Non-Convection Freestanding/Slide-In Control ProgrammingAfter unit is powered up, press the following keypad sequence
  • Sabbath Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass