mypros+
Model reference

KitchenAid KGST307BBL0

Range

10 documents52 error codes5 service modes

Available documentation

Tech Sheet

  • Wiring Sheet - 9751761 - Rev E1 pg
    Covers this model
  • TECH SHEET - KitchenAid Range KGST307BBL28 pg
    Covers this model
  • TECH SHEET8 pg
    Covers this model

Service Manual

  • Whirlpool KAC 22 Failure Codes Wiring Diagrams for Freestanding Slide in Ranges and Built in Ovens34 pg
    Covers this model
  • kac-22-whrlpl34 pg
    Covers this model
  • kitchenaid-failure32 pg
    Covers this model
  • Job Aid - 4317266 (KAC-22)33 pg
    Covers this model
  • Electronic Oven Controls - Job Aid 431726633 pg
    Covers this model

Other

  • Kitchenaid Range KGST307BBL2 Wiring Sheet 97526681 pg
    Covers this model
  • 431716993 pg
    Covers this model
MyPros+ Max

Diagnose your KitchenAid KGST307BBL0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (52)

CodeMeaning
F1Control out of calibrationF1-E0Electronics subsystem failureF1-E1Electronics subsystem failureF1-E2Electronics subsystem failureF1-E3Electronics subsystem failureF1-E5Electronics subsystem failureF1-E9Electronics subsystem failureF1E0EEPROM read fault (silent fault, not displayed).F1E1EEPROM checksum does not match at start key (silent fault, not displayed).F1E3Configuration jumper change; freestanding, electric switches or P9 pins 6 to 7…F1E4Q8 shorted.F1E9Stack overflow, highest priority.F2Keyboard shorted, Cancel not operating.F2-E0Keypad subsystem failureF2-E1Keypad subsystem failureF2-E4Keypad subsystem failureF2-E5Keypad subsystem failureF2E0Cancel key level too low (open).F2E2Cancel key loop test failed.F2E3Key held down too long or keyboard short.F2E4Keys unsettled probably due to noise.F3Oven probe shorted or open.F3-E0Cavity temperature sensor failureF3-E1Cavity temperature sensor failureF3-E2Cavity temperature sensor failureF3-E3Cavity temperature sensor failureF3E0Oven sensor open.F3E1Shorted oven sensor.F3E2Oven temp too high (runaway).F4Meat probe shorted.
View all 52 error codes
F4-E1Meat probe failureF4E1Meat probe shorted (less than 1500 ohms).F5Door signal inconsistent.F5-E0Latch subsystem failureF5-E1Latch subsystem failureF5-E3Latch subsystem failureF5-E5Latch subsystem failureF5-E7Latch subsystem failureF5E1Self clean latch lock make after 30 seconds.F5E3Loss of 120 VAC across L1 to Ground or Q19 circuit error.F5E5Self clean temperature not satisfied after 30 minutes.F5E6Door locked somehow with door open.F5E7Door unlocked somehow and will not unlatch.F6Ambient (console bimetal) sensor open (too hot).F6-E0Electronics over-temperatureF6-E1Electronics over-temperatureF6-E2Electronics over-temperatureF6E0Ambient (console bi-metal) sensor opened (too hot).F7Control or keypad switches shorted.F7-E0Digital switch signal (5 VDC @ 1kHz) failureF7E0Input switches won't follow their strobe level (shorted to ground).PFPower failure

Service modes (5)

  • F1E3 Configuration Reconfiguration ProcedureStep 1: Make sure harness to P1 connector is correct per wiring diagram. Step 2: Power down and…
  • F1E3 Configuration Reset["Verify harness to P1 connector is correct per wiring diagram.","STEP 1
  • Hidden Codes / Diagnostic AccessPress and hold each of the following pads for 5 seconds
  • Hidden Codes / Diagnostic ModePress and hold each of the following keypads for 5 seconds to access hidden functions
  • Temperature Calibration1

Full entry steps, exit procedures, and test sequences are available in Max.

Related KitchenAid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass