mypros+
Model reference

Maytag CER3525AAW

Range

10 documents36 error codes44 service modes

Available documentation

Tech Sheet

  • Electric Freestanding Range — Technical Information8 pg
    Covers this model
  • Electric Freestanding Range — Technical Information8 pg
    Covers this model

Service Manual

  • Service Manual - Freestanding Electric Range54 pg
    Covers this model
  • Freestanding Electric Range Service Manual54 pg
    Covers this model
  • range_maytagerrorcodes_joba124 pg
    Covers this model
  • Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model
  • Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
    Covers this model
  • FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
    Covers this model

Installation Guide

  • Installation Instructions18 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag CER3525AAW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (36)

CodeMeaning
1c1cShorted key detected; keypress disables audible for affected key depression.1c2cKeyboard tail disconnected; keyboard loop reading improper value.1c31Cancel key circuit problem; cancel key returning improper value.1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cPower micro communication failure (CRC invalid).1c6cEEPROM error; no response from EEPROM after 3 tries.1c7cControl not calibrated; calibration value out of range.1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error; CRC invalid when cook or clean is programmed.1d11Runaway oven temperature (650°F) with door unlocked; sensor resistance greater…1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Runaway oven temperature (950°F) with door locked; sensor resistance greater…1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Oven temperature sensor open; sensor resistance reading infinite ohms during…3d12Temperature sensor failure (open) on lower oven cavity3d21Oven temperature sensor shorted; sensor resistance reading 0 ohms during cook…3d22Temperature sensor failure (short) on lower oven cavity3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch not closed when door is locked; disables Clean and Lockout…4d12Door switch position failure4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch not open or closed (invalid state); turns off oven light and…4d52Door switch circuit failure
View all 36 error codes
9d11Latch will not lock; lock switch not closed when it should be locked.9d12Door latch will not lock on lower oven cavity9d21Door latch will not unlock on upper/single oven cavity9d22Door latch will not unlock on lower oven cavity9d31Door latch both locked and unlocked simultaneously on upper/single oven9d32Door latch both locked and unlocked simultaneously on lower oven

Service modes (44)

  • 24 Hour Clock TogglePress and hold Cancel and Delay pads for 3 to 5 seconds. Press More + or Less
  • Child Lock OutPress and hold Cancel and Cook & Hold pads for 3 to 5 seconds until beep sounds.
  • Clock Display TogglePress and hold Cancel and Clock pads for 3 to 5 seconds.
  • Clock Display Toggle (On/Off)["Press and hold Cancel and Clock pads for 3 to 5 seconds."]
  • Diagnostic Code Display1. Within 60 seconds of powering up the unit, press and hold the More + pad. 2. Cycle through…
  • Diagnostic Code Display Mode["Must be started within 60 seconds of powering up the control.","Press and hold More + pad within…
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
  • Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
  • Factory Default ResetPress and hold Cancel and Keep Warm pads for 3 to 5 seconds until beep sounds.
  • Faults Access (EOC III Controls)1
  • Faults Access (EOC III)1
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • One-Watt Standby Mode (NSC)Press and hold Cancel and Less
  • Oven Temperature Adjustment1. Press Bake pad. 2. Enter 550 on the digit pad. 3. Immediately press and hold Bake pad for 3 to 5…
  • Quick Test1
  • Quick Test Mode["Must be entered within the first 5 minutes after power up.","Press and hold Cancel and Broil pads…
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (EOC III)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
  • Sabbath Mode1
  • Service Mode (EOC III Controls)1
  • Service Mode (EOC III)1
  • Temperature Display (°F/°C toggle)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More + or Less
  • Temperature Display (F/C toggle)Press and hold Cancel and Bake pads for 3 to 5 seconds. Press More + or Less
  • Temperature Display Toggle (°F/°C)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More + or Less
  • Test Mode (UH Control)1
  • Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass