Model reference

Maytag JDS9860BDW21

Name: Maytag JDS9860BDW21
Brand: Maytag

Range

8 documents53 error codes32 service modes

Available documentation

Tech Sheet

Wiring Sheet - 8119P394-602 pg
Covers this model
Technical Information—Dual Fuel Slide-In Range11 pg
Covers this model

Service Manual

Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
Covers this model
Failure Codes And Wiring Diagrams For Maytag Heritage Gas & Electric Ranges124 pg
Covers this model

Service Flash

Service Pointer - 8178755 (Two Burner Cartridge)2 pg
Covers this model

Installation Guide

Instruction Sheet3 pg
Covers this model
Instruction Sheet1 pg
Covers this model

Quick Reference

Quick Reference Manual1 pg
Covers this model

MyPros+ Max

Diagnose your Maytag JDS9860BDW21.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Range

1c1c on my Maytag JDS9860BDW21

M+

Shorted key detected on the control

From Tech Sheet W15254616, p.28:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (53)

CodeMeaning

1c1cShorted key detected on the control circuit board keyboard.1c2cKeyboard tail disconnected or keyboard loop has improper value.1c31Cancel key circuit problem (cancel key improper value) on upper/single oven…1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cPower micro communication failure (CRC invalid).1c6cEEPROM error 1c7cControl not calibrated 1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1d11Runaway temperature (650°F) detected with door unlocked on upper/single oven…1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Runaway temperature (950°F) detected with door locked on upper/single oven…1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Temperature sensor failure (open) on upper/single oven cavity 3d12Temperature sensor failure (open) on lower oven cavity 3d21Temperature sensor failure (short) on upper/single oven cavity 3d22Temperature sensor failure (short) on lower oven cavity 3d41Meat probe shorted 3d51Meat probe not calibrated 4d11Door switch position failure 4d12Door switch position failure 4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error 4d32Reverse Airflow Fan state error 4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure 4d52Door switch circuit failure 9d11Door latch will not lock on upper/single oven cavity

View all 53 error codes

9d12Door latch will not lock on lower oven cavity 9d21Door latch will not unlock on upper/single oven cavity 9d22Door latch will not unlock on lower oven cavity 9d31Door latch both locked and unlocked simultaneously on upper/single oven 9d32Door latch both locked and unlocked simultaneously on lower oven F0-0No fault present.F1-1Oven temperature above 650°F (343°C) in bake mode.F1-3Oven temperature above 950°F (510°C) during a clean cycle.F1-5Cancel pad not responding.F1-7Membrane disconnected.F1-8Shorted key (pad) in membrane switch.F1-9Internal control communication errors.F1-ALock/unlock switch state not advancing to control.F1-COven door switch state not advancing to control.F1-EControl not calibrated.F1-FJumper not removed from printed circuit board (PCB).F1-HEEPROM error.F1-NInternal voltage for slave micro incorrect.F3-1Open or shorted oven temperature sensor.F8Shorted meat probe.F9-1Oven door will not lock.F9-2Oven door will not unlock.F9-3Oven door status is both locked and unlocked.

Service modes (32)

Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
Faults Access (EOC III Controls)1
Faults Access (EOC III)1
One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
One-Watt Standby Mode (NSC)Press and hold Cancel and Less
Quick Test ModePress and hold Cancel and Broil pads simultaneously for 3 seconds at power-up, or within 5 minutes…
Quick Test Mode (EOC III Controls)1
Quick Test Mode (EOC III)1
Quick Test Mode (H1 Controls - Convection Model)1
Quick Test Mode (H1 Controls - Non-Convection Model)1
Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H2/H2.5 Controls)1
Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (H3 Controls)1
Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
Quick Test Mode (M1/M2 Controls)1
Quick Test Mode (NSC Non-Self Clean Controls)1
Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
Service Mode (EOC III Controls)1
Service Mode (EOC III)1
Setup Options (Default Configuration)Press Setup Options and the desired pad simultaneously (see options table)
Test Mode (UH Control)1
Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass