mypros+
Model reference

Maytag MER5552BAW

Range

8 documents39 error codes28 service modes

Available documentation

Tech Sheet

  • techsheet-16026686.pdf9 pg
    Covers this model

Service Manual

  • 30" Freestanding Electric Ranges Base Manual55 pg
    Covers this model
  • Maytag Amana 30 Inch Freestanding Electric Range Service Manual55 pg
    Covers this model
  • Service Manual - 1602678455 pg
    Covers this model
  • Service - Electric Range Service Manual55 pg
    Covers this model
  • Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model
  • FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
    Covers this model

Bulletin

  • Technical Bulletin - TDC-0096-B-French Oven Door Handles Breaking2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MER5552BAW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (39)

CodeMeaning
1c1cShorted key detected on the control circuit board.1c2cKeyboard tail disconnected or keyboard loop has improper value.1c31Cancel key circuit problem (improper value).1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cMicro communication failure (checksum invalid).1c5cVcc or ground fault (Vcc/Gnd at test point).1c6cEEPROM error (no response from EEPROM).1c7cControl not calibrated (calibration value out of range).1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error (CRC invalid).1d11Runaway temperature (650°F) with door unlocked; sensor resistance > 2293 Ohms.1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Runaway temperature (950°F) with door locked; sensor resistance > 2662 Ohms.1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Oven temperature sensor open (resistance > infinite Ohms).3d12Temperature sensor failure (open) on lower oven cavity3d21Oven temperature sensor shorted (resistance > 0 Ohms).3d22Temperature sensor failure (short) on lower oven cavity3d41Meat probe shorted3d51Meat probe not calibrated4d11Door position switch not closed when door locked.4d12Door switch position failure4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure
View all 39 error codes
4d52Door switch circuit failure9d11Latch will not lock (lock switch not closed when Clean activated).9d12Door latch will not lock on lower oven cavity9d21Latch will not unlock (lock switch closed when Clean not activated).9d22Door latch will not unlock on lower oven cavity9d31Unlock state unknown9d32Door latch both locked and unlocked simultaneously on lower oven9d41Unlock state unknown9d51Lock switch not locked or unlocked.

Service modes (28)

  • 12-Hour Auto ShutoffControl automatically cancels cooking operations and removes relay drives 12 hours after the last…
  • 24-hour Clock Toggle["Press and hold Cancel and Delay pads for 3 to 5 seconds.","Press More+ or Less- pads to toggle…
  • Child Lockout["Press and hold Cancel and Cook & Hold pads for 3 to 5 seconds until beep sounds."]
  • Clock Display Toggle["Press and hold Cancel and Clock pads for 3 to 5 seconds."]
  • Diagnostic Code Display["Must be accessed within 30 seconds of powering up the control.","Press and hold the More+ pad…
  • Diagnostic Code Display Mode["Must be accessed within 30 seconds of powering up the control.","Press and hold More+ pad within…
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Factory Default Reset["Press and hold Cancel and Keep Warm pads for 3 to 5 seconds until beep sounds."]
  • Faults Access (EOC III Controls)1
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • Oven Temperature Adjustment["Press Bake pad.","Enter 550 on the digit-pad.","Immediately press and hold Bake pad for 3 to 5…
  • Quick Test1
  • Quick Test Mode["Must be entered within the first 5 minutes after power up.","Press and hold Cancel and Broil pads…
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Sabbath Mode["Initiate desired bake function before entering Sabbath mode.","Hold Clock pad for 3 to 5 seconds…
  • Service Mode (EOC III Controls)1
  • Temperature Display (°F/°C toggle)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More+ or Less- pads to change…
  • Temperature Display Toggle (°F/°C)Press and hold Cancel and Bake pads for 3 to 5 seconds. Press More + or Less
  • Temperature Display Toggle (F/C)Press and hold Cancel and Bake pads for 3 to 5 seconds
  • Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass