mypros+
Model reference

Maytag MGS5775BDB

Range

10 documents27 error codes10 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 16026292F (FR)12 pg
    Covers this model

Service Manual

  • Service Manual - 1602629355 pg
    Covers this model
  • Service Manual - Gas Slide-In Range55 pg
    Covers this model

Bulletin

  • Installation Bulletin1 pg
    Covers this model
  • Technical Bulletin - TDC-0096-B-French Oven Door Handles Breaking2 pg
    Covers this model
  • Technical Bulletin - TDC-0096-B Oven Door Handles Breaking2 pg
    Covers this model

Service Flash

  • Technical Bulletin - TDC-0096-B Oven Door Handles Breaking_TDC-0096-B2 pg
    Covers this model

Other

  • TDC 0099 B1 pg
    Covers this model
  • TDC 0096 B2 pg
    Covers this model

Installation Guide

  • Installation Bulletin2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MGS5775BDB.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (27)

CodeMeaning
1c1cIncorrect key value detected by the control.1c2cIncorrect key value cancellation1c31No response from EEPROM.1c32Calibration value out of limits.1c6cDisables buzzer for key press.1c7cDisables all outputs (control-related fault).1c8cIncorrect cyclic redundancy check.1d11Oven sensor resistance greater than 2237 ohms (upper/single cavity, open…1d12Oven sensor resistance greater than 2237 ohms (upper/single cavity, second…1d21Oven sensor resistance greater than 2787 ohms (lower cavity, open circuit high).1d22Oven sensor resistance greater than 2787 ohms (lower cavity, second occurrence).3d11Meat probe sensor resistance is infinite (open circuit).3d12Meat probe sensor resistance is infinite (second occurrence).3d21Meat probe sensor resistance is 0 ohms (short circuit).3d22Meat probe sensor resistance is 0 ohms (second occurrence).4d11Door switch not closed when door is locked.4d12Door switch not closed when door is locked (second occurrence).4d21No rotation of air flow reversal fan (0/low RPM).4d31Air flow reversal fan state is on instead of off.4d51Door switch is neither open nor closed.4d52Door switch is neither open nor closed (second occurrence).9d11Lock switch not closed (lock position not detected).9d12Lock switch not closed (second occurrence).9d21Unlock switch not closed (unlock position not detected).9d22Unlock switch not closed (second occurrence).9d31Door lock is simultaneously in locked and unlocked position.9d32Door lock is simultaneously in locked and unlocked position (second occurrence).

Service modes (10)

  • Control Panel Membrane Switch Continuity TestPress and hold Autoset 0 while powering on the appliance.
  • Diagnostic Code Display ModePress and hold the Autoset key for 5 seconds during power-up
  • H1 Diagnostic Code Display1
  • H1 Quick Test Mode1
  • M1 Diagnostic Code Display1
  • M1 Quick Test Mode1
  • M2 Diagnostic Code Display1
  • M2 Quick Test Mode1
  • Quick Test ModePress and hold Cancel and Broil keys simultaneously for 5 seconds at startup or within 5 minutes of…
  • Temperature Calibration AdjustmentPress Bake key and enter 550°F

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass