mypros+
Model reference

Maytag M-17

Washer

1 document22 error codes10 service modes

Available documentation

Service Manual

  • Maytag® 3.5 cu. ft. Commercial-Grade Residential Agitator Washer Technical Manual67 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag M-17.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
F0E2Over suds condition detected; suds prevent the basket from spinning up to speed…F0E4High water temperature detected during rinse cycle (water temperature 105°F /…F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2E1Stuck key; the START key has been actuated for 10 consecutive minutes.F2E3Mismatch of main control and UI; the User Interface identification does not…F3E1Pressure sensor fault; the main control detects an out of range pressure signal.F3E2Inlet water temperature fault; the inlet thermistor is detected to be open or…F5E1Lid switch fault; lid is in locked state but lid switch is open, or main…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket, or…F7E5Shifter fault; the main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold water supply hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (10)

  • Calibration Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Clean Washer Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Drain and Spin Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Manual Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until FINAL…
  • Quick Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until…
  • UI Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass