mypros+
Model reference

Maytag MVWC465HW4

Washer

15 documents43 error codes18 service modes

Available documentation

Tech Sheet

  • FOR SERVICE TECHNICIAN'S USE ONLY - Tech Sheet44 pg
    Covers this model
  • Service Technical Sheet W1074057344 pg
    Covers this model

Service Manual

  • Manual Maytag Centennial Washers1 pg
    Covers this model
  • Technical Education Job Aid 8178628 ML-3 Top-load Washer Centennial™60 pg
    Covers this model
  • Vertical Modular Washer84 pg
    Covers this model
  • Vertical Modular Washer84 pg
    Covers this model

Service Flash

  • Technical Service Pointer6 pg
    Covers this model
  • Service Pointer - W11648603 - Rev A - Top Load Washers Two-Step Start Behavior Change6 pg
    Covers this model
  • Service Pointer - W11766193 - Rev F - Top Load Washer and Stacked Laundry - F3E1 Pressure Sensor Error or Drain Pump Running Continuously9 pg
    Covers this model
  • Technical Service Pointer12 pg
    Covers this model
  • Technical Service Pointer - Noise During Spin6 pg
    Covers this model
  • Technical Service Pointer - Pressure Dome Port Flash7 pg
    Covers this model

Quick Reference

  • Manual de referencia rápida1 pg
    Covers this model
  • Quick Start Guide2 pg
    Covers this model
  • Manual de referencia rápida1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MVWC465HW4.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (43)

CodeMeaning
F0 E2Over suds condition detectedF0 E4High water temperature during rinse cycleF0 E5Off balance load detected.F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1 E1Main control fault.F1 E2Motor control faultF1E1Main control fault.F1E2Motor control fault on the main control board.F2 E1Stuck keyF2 E3Mismatch of main control and UIF2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Switch mismatch; the switches do not match the console or are not operating…F3 E1Pressure sensor faultF3 E2Inlet water temperature faultF3E1Pressure system fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected open or shorted.F5 E1Lid switch faultF5 E2Lid lock faultF5 E3Lid unlock faultF5 E4Lid not opened between cyclesF5E1Lid switch fault; lid is in locked state but lid switch is open, control not…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7 E1Basket speed sensor faultF7 E5Shifter faultF7 E6Motor fault
View all 43 error codes
F7 E7Motor unable to reach target RPMF7E1Basket speed fault; main control cannot determine speed of basket or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8 E1No fill / long fillF8 E3Overflow conditionF8 E5Hot and cold water supply hoses are reversed.F8E1No fill / long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9 E1Long drainF9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (18)

  • Automatic Test Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Spin' LED is On and '02' is…
  • automatic_test1
  • calibration1
  • Calibration Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse' LED is On and '04' is…
  • diagnostic1. Washer must be in standby mode (plugged in, all indicators off). Wait 10 seconds after initial…
  • Fault Code Display Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Done' LED is On and '01' is…
  • fault_code_display1
  • Manual Test Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Spin & Done' LEDs are On and…
  • manual_test1
  • Sales Demo Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse & Done' LEDs are On and…
  • Service Diagnostic Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse, Spin, and Done' LEDs are…
  • sw_version_display1
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are…
  • tachometer_verification1
  • UI Test Mode["Enter Service Diagnostic Mode.","Turn cycle selector knob until 'Rinse & Spin' LEDs are On and…
  • ui_test1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass