Model reference
Maytag MVWP575GW1
Washer
4 documents23 error codes12 service modes
Available documentation
Tech Sheet
- TechSheet W11045666 RevA40 pg
Service Manual
- Maytag® 3.5 cu. ft. Commercial-Grade Residential Agitator Washer Technical Manual67 pg
Installation Guide
- Installation Instructions20 pg
Quick Reference
- Quick Start Guide2 pg
MyPros+ Max
Diagnose your Maytag MVWP575GW1.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (23)
CodeMeaning
F0E0No fault detected.F0E2Over suds condition detected; suds prevent the basket from spinning up to speed…F0E4High water temperature detected (105°F / 41°C or higher) during rinse cycle.F0E5Off balance load detected during operation.F1E1Main control fault.F1E2Motor control fault on the main control board.F2E1Stuck key fault; the START key has been actuated for 10 consecutive minutes.F2E3Mismatch of main control and user interface; the UI identification does not…F3E1Pressure sensor fault; the main control detects an out of range pressure signal.F3E2Inlet water temperature fault; the inlet thermistor is detected to be open or…F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; the main control cannot determine speed of basket or…F7E5Shifter fault; the main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold water supply hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain; water level does not change after the drain pump is on for 10…Service modes (12)
- Calibration Mode["Enter Diagnostic Test Mode.","Toggle cycle selector knob until RINSE LED is ON.","Press START…
- Clean Washer Cycle["Enter Diagnostic Test Mode.","Toggle cycle selector knob until SOAK/WASH, RINSE, FINAL SPIN, and…
- Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
- Drain & Spin Cycle["Enter Diagnostic Test Mode.","Toggle cycle selector knob until RINSE and DONE LEDs are…
- Drain and Spin Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
- Fault Code Display Mode["Enter Diagnostic Test Mode.","Toggle cycle selector knob until only the DONE LED is ON.","Press…
- Manual Overview Test Mode["Enter Diagnostic Test Mode.","Toggle cycle selector knob until FINAL SPIN and DONE LEDs are…
- Quick Overview Test Mode["Enter Diagnostic Test Mode.","Toggle cycle selector knob until FINAL SPIN LED is ON.","Press…
- Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
- Software Version Display Mode["Enter Diagnostic Test Mode.","Toggle cycle selector knob until RINSE, FINAL SPIN, and DONE LEDs…
- Tachometer Verification Mode["Enter Diagnostic Test Mode.","Toggle cycle selector knob until SOAK/WASH and DONE LEDs are…
- UI Test Mode["Enter Diagnostic Test Mode.","Toggle cycle selector knob until RINSE and FINAL SPIN LEDs are…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Maytag washer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass