Model reference

Thermador 58300000211965

Cooktop

1 document91 error codes2 service modes

Available documentation

Service Manual

Thermador Induction Cooktop Error Codes32 pg
Covers this model

MyPros+ Max

Diagnose your Thermador 58300000211965.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Thermador Cooktop

E0101 on my Thermador 58300000211965

M+

Left ADB relay board incorrect or

From Service Manual 478111, p.43:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part 00630783

Door lock assembly

Error codes (91)

CodeMeaning

E0101Left ADB relay board incorrect or faulty firmware E0102Left ADB relay board error in the microcontroller's internal memory (EEPROM)E0114Left ADB communication error or poor quality communication between the…E0116Left ADB communication error or poor quality communication between induction…E0131Left ADB error in the supply voltage synchronisation signal E0133Left ADB error checking induction module component: induction hob configuration…E0137Fault in the unit's temperature sensor (NTC on the front), left ADB E0139Left ADB error checking induction module component: microcontroller E013ALeft ADB error checking induction module component: inductor activation relay E013BLeft ADB error checking induction module component: inductor activation relay E013CLeft ADB error checking induction module component: NTC selection circuit E013DLeft ADB error checking induction module component: relay activation circuit E0142Left ADB error checking induction module component: A/D current converter E0145Left ADB error checking induction module component: the module's temperature…E0146Left ADB error checking induction module component: pot detection sensor E0147Left ADB induction module has been unable to correctly detect its position in…E0201Power board (PB) incorrect or faulty firmware E0202Power board (PB) error in the microcontroller's internal memory (EEPROM)E0208The fan is not working.E0212Power board error checking induction module component: communication between…E0215Error in the communication protocol between the operating modules and the…E0231Power board error in the supply voltage synchronisation signal E0232Power board error checking induction module component: input relay E0236Power board error checking induction module component: input relay E0239Power board error checking induction module component: microcontroller E0240Power board error checking induction module component: input relay E0241Power board error checking induction module component: power stage E0242Power board error checking induction module component: A/D current converter E0243Power board error checking induction module component: A/D supply voltage…E0244Power board error checking induction module component

View all 91 error codes

E0245Power board error checking the induction module E0246Power board error checking induction module component: input relay E0248Power board error checking induction module component: A/D supply voltage…E0301Right ADB relay board incorrect or faulty firmware E0302Right ADB relay board error in the microcontroller's internal memory (EEPROM)E0314Right ADB communication error or poor quality communication between the…E0316Right ADB communication error or poor quality communication between induction…E0331Right ADB error in the supply voltage synchronisation signal E0333Right ADB error checking induction module component: induction hob…E0337Fault in the unit's temperature sensor (NTC on the front), right ADB E0339Right ADB error checking induction module component: microcontroller E033ARight ADB error checking induction module component: inductor activation relay E033BRight ADB error checking induction module component: inductor activation relay E033CRight ADB error checking induction module component: NTC selection circuit E033DRight ADB error checking induction module component: relay activation circuit E0342Right ADB error checking induction module component: A/D current converter E0345Right ADB error checking induction module component: the module's temperature…E0346Right ADB error checking induction module component: pot detection sensor E0347Right ADB induction module has been unable to correctly detect its position in…E0513DBUS2 communication failure between the modules E0516Communication error between the cooking sensor module (YL245) and the Bluetooth…E0517Error in the internal communication protocol of the operating module.E0521Overheating in the operating module E0522Overheating in the operating module E0523Overheating in the operating module caused by a hot pot near the operating…E0721Overheating in the Active Light module E0722Overheating in the Active Light module E0723Error checking Active Light component: LEDs E2101Inductor not connected on left ADB.E2130Fault in the inductor temperature sensor (faulty NTC) on left ADB.E2131Fault in the inductor temperature sensor (NTC not connected) on left ADB.E2132Fault in the inductor temperature sensor (NTC not connected or incorrectly…E2301Inductor not connected on right ADB.E2330Fault in the inductor temperature sensor (faulty NTC) on right ADB.E2331Fault in the inductor temperature sensor (NTC not connected) on right ADB.E2332Fault in the inductor temperature sensor (NTC not connected or incorrectly…E7010Communication failure with the Home Connect module.E7015Overheating in the Home Connect module E7101Home Connect module not configured E8202Cooking sensor overheating E8203Cooking sensor overheating E8204Cooking sensor battery almost worn out E8205The cooking sensor (wireless cooking sensor) has lost communication with the…E8206Error checking cooking sensor components: thermopile E8207Overheating of the Bluetooth board E8208Overheating of the Bluetooth board E8209The cooking sensor has become detached from the pot when using the cooking…E8210The cooking sensor has become detached from the pot when using the cooking…E9000Supply voltage below the expected value (approximately Vrms < 150 V).E9010Supply voltage above the expected value (approximately Vrms > 270 V).E9011Supply voltage much higher than expected F0123Overheating of the electronics of the left ADB induction module: electronic…F0222Overheating of the electronics of the induction module: power stage F0223Overheating of the electronics of the power board (PB) induction module…F0224Overheating of the external NTC sensor F0323Overheating of the electronics of the right ADB induction module: electronic…F2120Inductor overheating on left ADB F2320Inductor overheating on right ADB F8Automatic disconnection of a cooking zone F9100Demo mode is active U400Supply voltage much higher than expected

Service modes (2)

Demo ModeActivate via basic settings menu; select Demo Mode and set to ON.
Inductors Test (Service Menu)Access the customer service menu, navigate to the 'Inductors Test' step

Full entry steps, exit procedures, and test sequences are available in Max.

Related Thermador cooktop models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass