mypros+
Error code reference

Thermador Cooktop Error Code E2130

Fault in the inductor temperature sensor (faulty NTC) on left ADB.

Thermador codesThermador cooktop codes

Fault in the inductor temperature sensor (faulty NTC) on left ADB.

First step from the service manual

Check the wiring of the NTC and make sure it is connected to the correct ADB connector.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E2130.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E2130 means on a Thermador cooktop

The E2130 error code indicates a fault in the inductor temperature sensor, specifically the NTC (Negative Temperature Coefficient) thermistor, located on the left ADB (Actuator Driver Board). The NTC thermistor is a resistive sensor whose resistance decreases as temperature increases, allowing the control system to monitor the temperature of the induction coil assembly in real time. When the cooktop's control system detects that the NTC signal is outside the expected resistance or voltage range, it logs this fault and may disable the affected cooking zone to prevent overheating or unsafe operation.

The left ADB is a dedicated board responsible for driving and monitoring the induction components on the left side of the cooktop. The NTC sensor connects directly to this board via a specific connector, and the board continuously interprets the sensor's resistance to regulate power output and thermal protection. A fault can originate from the sensor itself, the wiring harness between the sensor and the ADB, or a poor connection at the ADB connector.

The first diagnostic step is to inspect the NTC wiring and confirm it is seated in the correct connector on the left ADB. Swapped or misrouted connectors are a common installation or reassembly error that can trigger this code immediately. If wiring is confirmed correct, the NTC thermistor should be tested for proper resistance values across its operating temperature range, and the ADB itself should be evaluated if the sensor and wiring check out normal.

Source: manufacturer service documentation.

Common causes of E2130

  1. 01

    Disconnected or misrouted NTC connector on the left ADB

    Wiring / connection

    The NTC sensor connector may be unplugged, seated in the wrong port on the left ADB, or only partially connected. This is the first thing to check and is a common cause after any prior service work on the unit.

  2. 02

    Damaged or broken NTC wiring harness

    Part replacement

    The wiring between the NTC thermistor and the left ADB can develop breaks, shorts, or chafed insulation, especially near areas where the harness is routed close to heat sources or sharp edges. Inspect the full length of the harness for visible damage.

  3. 03

    Failed NTC thermistor

    Part replacement

    The NTC sensor itself can fail open or short internally, producing a resistance reading that falls outside the expected range for the cooktop's control system. A faulty sensor will need to be replaced.

  4. 04

    Corroded or loose connector pins at the ADB

    Wiring / connection

    Moisture or heat exposure can cause corrosion on the connector pins where the NTC harness attaches to the left ADB. This increases resistance at the connection point and can mimic a sensor failure. Inspect pins for oxidation and ensure the connector is fully seated.

  5. 05

    Faulty left ADB

    Part replacement

    If the NTC sensor and all wiring test within normal specifications, the left ADB itself may have failed and is misinterpreting the sensor signal. Board replacement should only be considered after all other components have been ruled out.

See the test procedure for each cause

Frequently asked questions about E2130

What does E2130 mean on a Thermador cooktop?
E2130 indicates a fault in the NTC inductor temperature sensor on the left ADB (Actuator Driver Board). The NTC is a thermistor that monitors the temperature of the induction coil assembly, and this code appears when the control system reads a signal outside the expected parameters. The cooktop may disable the affected left zone as a protective measure until the fault is resolved.
Can I fix E2130 myself or do I need a technician?
Some causes of E2130 are within reach for a knowledgeable DIYer, particularly checking and reseating the NTC connector on the left ADB. However, testing the NTC thermistor for proper resistance values and diagnosing the ADB board requires a multimeter and comfort working with disassembled appliance electronics. If you are not experienced with appliance repair, a qualified technician is recommended to avoid damaging components or voiding any remaining warranty.
Is it safe to keep using my cooktop with the E2130 code active?
It is not recommended to continue using the affected cooking zone while E2130 is active. The NTC sensor is part of the cooktop's thermal protection system, and operating without a functioning temperature sensor means the cooktop cannot properly monitor for overheating on the left side. This could pose a safety risk. Other zones may continue to function, but the faulty zone should remain unused until the issue is repaired.
Will resetting the cooktop clear the E2130 error?
A power reset may temporarily clear the E2130 code, but it will return if the underlying fault in the NTC sensor, wiring, or ADB connection is not corrected. Resetting by cycling the breaker or unplugging the unit does not fix the root cause. The fault must be diagnosed and repaired for the code to stay cleared.
How much does it cost to repair the E2130 error on a Thermador cooktop?
Repair costs vary depending on the root cause. If the fix is simply reseating a loose connector, you may only pay a service call fee, typically in the range of $80 to $150. Replacing the NTC thermistor itself is a relatively low-cost part, but if the left ADB requires replacement, parts alone can range from $150 to $400 or more, with labor adding to the total. Getting a diagnostic visit from a certified technician will give you a more accurate estimate for your specific situation.

Related Thermador cooktop codes

All Thermador cooktop codes
View all 129 Thermador cooktop codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass