Model reference
Whirlpool WGD9450WR2
Dryer
8 documents25 error codes12 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10251192 - Rev A16 pg
- Tech Sheet - W1029885056 pg
- Whirlpool Dryer YWED9500TW3 Tech Sheet56 pg
Service Flash
- Service Pointer - 8178790 (Door not Closing)6 pg
Tech Tip
- Instruction Sheet - W10128087- Rev A - Special Handling7 pg
- Instruction Sheet2 pg
- Instruction Sheet12 pg
Installation Guide
- Instrucciones de instalacion16 pg
MyPros+ Max
Diagnose your Whirlpool WGD9450WR2.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (25)
CodeMeaning
afLow inlet air flow condition detected at installation (Amana models only).f:01Primary control failure.f:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).f:20Heater failuref:22Outlet thermistor is open.f:23Outlet thermistor has shorted.f:24Inlet thermistor is open (Amana models only, appears ONLY in Diagnostic Test…f:25Inlet thermistor is shorted (Amana models only, appears ONLY in Diagnostic Test…f:26Motor drive system failure.f:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).f:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).f:30Restricted air flow condition exists (Amana models only, appears ONLY in…f:31L2 line voltage errorf:50Water valve failuref:70No communication between the machine control and the console electronics.f:71No communication between the machine control and the console electronics.f:72Console electronics failure (F:72 through F:78).f:73Console electronics failure (F:72 through F:78).f:74Console electronics failure (F:72 through F:78).f:75Console electronics failure (F:72 through F:78).f:76Console electronics failure (F:72 through F:78).f:77Console electronics failure (F:72 through F:78).f:78Console electronics failure (F:72 through F:78).l2Low line voltage (less than 30V) detected at installation.pfPower failure occurred while the dryer was running.Service modes (12)
- Customer-Focused Drying Mode Adjustment["In Standby mode (dryer plugged in but not powered up), press and hold the Dryness Level button…
- Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)1
- Diagnostic Test Mode1. Dryer must be in standby mode (plugged in with all indicators off, or with only Done/Dry/Clothes…
- Displaying Inlet Air Flow Diagnostic (Amana Electric Models Only)["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
- Displaying Line Voltage Diagnostic["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
- Dryness Level Adjust (CF Mode)["Dryer must be in Standby mode (plugged in but not powered up).","Press and hold the Dryness Level…
- Inlet Air Flow Diagnostic (Amana Electric Models Only)After entering the Diagnostic Test Mode and cycling through saved fault codes, press the Wrinkle…
- Inlet Air Flow Test (Electric Models Only)After entering Diagnostic Test Mode, waiting for the 5 second delay, and cycling through any saved…
- Line Voltage DiagnosticAfter entering the Diagnostic Test Mode and cycling through saved fault codes, press the Cycle…
- Line Voltage Display["Enter Diagnostic Test Mode.","Wait for the 5 second delay.","Cycle through any saved fault…
- Line Voltage Display TestAfter entering Diagnostic Test Mode, waiting for the 5 second delay, and cycling through any saved…
- Manual Load Test1. Dryer must be in standby mode. 2. Select any one button except Pause/Cancel and Controls…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool dryer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass