Model reference

Whirlpool YWED9500TU1

Dryer

7 documents25 error codes5 service modes

Available documentation

Tech Sheet

Tech Sheet - W10177457A16 pg
Covers this model
Whirlpool Dryer YWED9500TW3 Tech Sheet56 pg
Covers this model

Tech Tip

Instruction Sheet - W10128087- Rev A - Special Handling7 pg
Covers this model
Instruction Sheet2 pg
Covers this model

Quick Reference

Quick Reference Manual2 pg
Covers this model

Installation Guide

Installation Instructions32 pg
Covers this model
Instrucciones de instalacion16 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool YWED9500TU1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Dryer

af on my Whirlpool YWED9500TU1

M+

Low inlet air flow condition detected

From Tech Sheet W13558427, p.39:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (25)

CodeMeaning

afLow inlet air flow condition detected at installation (Amana models only).f:01Primary control failure.f:02Stuck button or user interface mismatch (appears only in Diagnostic Test Mode).f:20Heater failure f:22Outlet thermistor is open.f:23Outlet thermistor has shorted.f:24Inlet thermistor is open (Amana models only, appears only in Diagnostic Test…f:25Inlet thermistor has shorted (Amana models only, appears only in Diagnostic…f:26Motor drive system failure.f:28Moisture sensor strip is open (appears only in Diagnostic Test Mode).f:29Moisture sensor strip has shorted (appears only in Diagnostic Test Mode).f:30Restricted air flow condition exists (Amana models only, appears only in…f:31L2 line voltage error f:50Water valve failure f:70No communication between the machine control and the console electronics.f:71No communication between the machine control and the console electronics.f:72Console electronics failure (F:72 through F:78).f:73Console electronics failure (F:72 through F:78).f:74Console electronics failure (F:72 through F:78).f:75Console electronics failure (F:72 through F:78).f:76Console electronics failure (F:72 through F:78).f:77Console electronics failure (F:72 through F:78).f:78Console electronics failure (F:72 through F:78).l2Low line voltage (less than 30V) detected at installation.pfPower failure occurred while the dryer was running.

Service modes (5)

Customer-Focused Drying Mode Adjustment (CF1/CF2/CF3)["In standby mode (dryer plugged in but not powered up), press and hold the Dryness Level (Sensor…
Diagnostic Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the…
Displaying Inlet Air Flow Diagnostic (Amana Electric Models Only)["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
Displaying Line Voltage Diagnostic["Enter the Diagnostic Test Mode.","Wait for the 5 second delay and cycle through any saved fault…
Manual Load Test["Ensure dryer is in standby mode (plugged in with all indicators off, or with only the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass