mypros+
Model reference

Whirlpool W10838047B

Washer

1 document23 error codes10 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10838047 - Rev B40 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool W10838047B.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (23)

CodeMeaning
F0E0No fault detected.F0E2Oversuds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature (105°F/41°C or higher) detected during rinse cycle.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the main control board.F2E1Stuck key; the START key has been actuated for 10 consecutive minutes.F2E3Mismatch of main control and user interface identification.F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user pressed START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM.F8E1Long fill; water level does not change for a period of time or water is present…F8E3Overflow condition; main control senses water level exceeding washer capacity.F8E5Hot and cold water inlet hoses are reversed.F8E6No fill; water level does not change for a period of time or water is present…F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (10)

  • Calibration Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until only the 'Rinse' LED is…
  • Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'In Use', 'Soak/Wash'…
  • Drain & Spin Cycle["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' and 'Done' LEDs…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes (see entry sequence above).","Toggle cycle selector knob…
  • Manual Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Final Spin' and 'Done'…
  • Quick Overview Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until only the 'Final Spin' LED…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse', 'Final Spin'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Soak/Wash' and 'Done'…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Toggle cycle selector knob until 'Rinse' and 'Final Spin'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass