Model reference
Whirlpool W11449150
Washer
1 document24 error codes15 service modes
Available documentation
Service Manual
- Tech Manual - W11449150 - Rev A16 pg
MyPros+ Max
Diagnose your Whirlpool W11449150.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (24)
CodeMeaning
d 13Coin 2 error; the Coin 2 sensor is detected as blocked for 8 seconds.d 16Generation 2 debit card reader error; no communication from installed debit…d5Coin 1 error; the Coin 1 sensor is detected as blocked for 8 seconds.d9Low voltage detection error; incoming voltage detected below 90 VAC for 8…F 01Communication error within the Central Control Unit (CCU); the pump drive in…F 04Accelerometer component failed; the X, Y, and Z limits are outside of the…F 11Motor Control Unit (MCU) has a failure, possibly due to a repeating under or…F 20No water detected entering washer; first level of pressure sensor not reached…F 21Long drain; drain time exceeds 8 minutes without reaching reset level in…F 22Door lock error; washer makes several attempts to lock the door and fails after…F 24Water temperature sensor value is out of range (23°F to 217°F / -5°C to 103°C).F 25Tachometer error; MCU is unable to properly detect motor speed and the washer…F 26Door switch error; the door switch circuit is open for 5 seconds while the door…F 27Overflow condition; the overflow contact on the pressure sensor is closed for…F 28Communication failure between CCU and MCU.F 29Door unlock error; the door is unable to unlock after 6 tries.F 31Overheating of motor; the heat sink exceeds 212°F (100°C)F 33Pump disconnected; the electrical connection between the pump and the CCU is…F 34Load detected in washer during Washer Cleanout Cycle.F 37Water level out of range low; water level has been detected to be below the…F 38Water level out of range high; water level has been detected to be above the…F 70Communication failure between CCU and User Interface (UI).F 73UI failure; communication error within the User Interface, possibly due to a…F 74UI failure (listed as secondary code under F73 section context).Service modes (15)
- Help Mode (dAS Mode)1
- Help Mode (PD Models)1
- P-01 Cancel Cycle, Reset Errors, and Clear EscrowFrom Service Diagnostic Test Modes, navigate to P-01 display and press START
- P-02 Cycle CreditFrom Service Diagnostic Test Modes, navigate to P-02 display and press START.
- P-03 Quick Overview TestFrom Service Diagnostic Test Modes, navigate to P-03 display and press START.
- P-04 Manual Overview TestFrom Service Diagnostic Test Modes, navigate to P-04 display and press START.
- P-05 Button TestFrom Service Diagnostic Test Modes, navigate to P-05 display and press START
- P-06 Drain and SpinFrom Service Diagnostic Test Modes, navigate to P-06 display and press START.
- P-07 UI DiagnosticsFrom Service Diagnostic Test Modes, navigate to P-07 display and press START
- P-08 Clean Washer CycleFrom Service Diagnostic Test Modes, navigate to P-08 display and press START.
- P-09 Factory DiagnosticsFrom Service Diagnostic Test Modes, navigate to P-09 display and press START.
- Service Access Code1
- Service Diagnostic Test Modes1
- Set-Up Mode (COIN models)Insert access door key, turn, and lift to remove access door
- Set-Up Mode (NON-COIN models via service connector)1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool washer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass