Model reference

Whirlpool W11580853

Name: Whirlpool W11580853
Brand: Whirlpool

Washer

1 document22 error codes11 service modes

Available documentation

Tech Sheet

Tech Sheet - W11580853 - Basic Operation of Commercial Front-Load Washer40 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool W11580853.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Washer

d13 on my Whirlpool W11580853

M+

Coin 2 error; the Coin 2 sensor is

From Tech Sheet W13184478, p.50:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part W10810403

Door lock assembly

Error codes (22)

CodeMeaning

d13Coin 2 error; the Coin 2 sensor is detected as blocked for 8 seconds.d16Generation 2 debit card reader error; no communication from installed debit…d5Coin 1 error; the Coin 1 sensor is detected as blocked for 8 seconds.d9Low voltage detection error; incoming voltage detected below 90 VAC for 8…F01Communication error within the Central Control Unit (CCU); the pump drive in…F04Accelerometer component failed; the X, Y, and Z limits are outside of the…F11Motor Control Unit (MCU) has a failure, possibly due to a repeating under or…F20No water detected entering washer; the first level of the pressure sensor is…F21Long drain; the drain time exceeds 8 minutes without reaching reset level in…F22Door lock error; washer made several attempts to lock the door without success…F24Water temperature sensor value is out of range (23°F to 217°F [-5°C to 103°C]).F25Tachometer error; MCU is unable to properly detect motor speed, washer shuts…F26Door switch error; the door switch circuit is open for 5 seconds while the door…F27Overflow conditions; the overflow contact on the pressure sensor is closed for…F28Communication failure between CCU and MCU.F29Door unlock error; the door is unable to unlock after 6 tries.F31Overheating of motor; the heat sink exceeds 212°F (100°C)F33Pump disconnected; the electrical connection between the pump and the CCU is…F34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and User Interface (UI).F73Communication error within the User Interface (UI).F74Communication error within the User Interface (UI).

Service modes (11)

Cycle Credit["Enter Washer Diagnostic Mode (display flashing).","Press the HOT button (CC will display)."]
Help Mode (dAS mode)["Enter set-up mode.","The message dAS will appear in the display.","Press the HOT button.","Press…
Help Mode (Manual Communication)["Enter set-up mode.","Press the WARM button until the set-up code 2.XX is on display.","Press the…
Manual Overview Test["Enter Washer Diagnostic Mode (display flashing).","Press the COTTON/WHITES button."]
Quick Overview Test["Enter Washer Diagnostic Mode (display flashing).","Press the WARM button."]
Quick Spin Cycle["Enter Washer Diagnostic Mode (display flashing).","Press the PERM PRESS button."]
Service Access Code["Press the upper left button.","Press the lower right button.","Press the upper right…
Set-Up Mode (9150 Models)["Insert access door key, turn, and lift to remove access door."]
Set-Up Mode (9160 Models via AA1 connector)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
Washer Cleanout Cycle["Enter Washer Diagnostic Mode (display flashing).","Press the COLORS/DELICATES button."]
Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (set-up mode).","Press and hold the COLD button for 2…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass