Model reference
Whirlpool W11616633
Washer
1 document22 error codes15 service modes
Available documentation
Service Manual
- Tech Manual - W11616633 - Rev A36 pg
MyPros+ Max
Diagnose your Whirlpool W11616633.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (22)
CodeMeaning
d13Coin 2 error; the Coin 2 sensor is detected as blocked for 8 seconds.d16Generation 2 debit card reader error; no communication from installed debit…d5Coin 1 error; the Coin 1 sensor is detected as blocked for 8 seconds.d9Low voltage detection error; incoming voltage detected below 90 VAC for 8…F01Communication error within the Central Control Unit (CCU); the pump drive in…F04Accelerometer component failed; the X, Y, and Z limits are outside of the…F11Motor Control Unit (MCU) has a failure, possibly due to a repeating under or…F20No water detected entering washer; the first level of the pressure sensor is…F21Long drain; the drain time exceeds 8 minutes without reaching reset level in…F22Door lock error; washer makes several attempts to lock the door and fails after…F24Temperature sensor error; water temperature sensor value is out of range (23°F…F25Tachometer error; the MCU is unable to properly detect motor speed, the washer…F26Door switch error; the door switch circuit is open for 5 seconds while the door…F27Overflow conditions; the overflow contact on the pressure sensor is closed for…F28Communication failure between CCU and MCU.F29Door unlock error; the door is unable to unlock after 6 tries.F31Overheating of motor; the heat sink exceeds 212°F (100°C)F33Pump disconnected; the electrical connection between the pump and the CCU is…F34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and User Interface (UI).F73Communication error within the User Interface (UI).F74Communication error within the User Interface (UI).Service modes (15)
- Code Display Sub-Mode (9150 models)["Open the service door.","The current F code or d code will be displayed."]
- Code Display Sub-Mode (9160 models)["Remove the AA1 connector from the UI board or insert a manual diagnostic card.","Or enter the…
- Flashing Mode (9150 models)["Open the service door.","Press and hold the COLD button until display segments are flashing."]
- Flashing Mode (9160 models)["Remove the AA1 connector or insert a manual diagnostic card."]
- Help Mode (dAS mode)["Enter set-up mode.","The message dAS will appear in the display.","Press the HOT button.","Press…
- Help Mode (Manual Communication)["Enter set-up mode.","Press the WARM button until the set-up code 2.XX is on display.","Press the…
- Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the COTTON/WHITES button."]
- Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the WARM button."]
- Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the PERM PRESS button."]
- Service Access Code (no console removal)["Press the upper left button.","Press the lower right button.","Press the upper right…
- Set-Up Mode (9150 models)["Insert access door key, turn, and lift to remove access door."]
- Set-Up Mode (9160 models via AA1 connector)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
- Set-Up Mode (9160 models via set-up card)["Insert a set-up card (supplied by the reader manufacturer) into the card slot."]
- Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the COLORS/DELICATES button."]
- Washer Diagnostic Mode["First enter Start Operating Set-Up (set-up mode).","Press and hold the COLD button for 2 seconds…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool washer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass