mypros+
Model reference

Whirlpool WFL98HEBU0

Washer

9 documents40 error codes6 service modes

Available documentation

Tech Sheet

  • Whirlpool Control Panel Service Technical Sheet56 pg
    Covers this model
  • Whirlpool FL DD Washer WFW97HEXL2 Tech Sheet W1050753556 pg
    Covers this model

Service Flash

  • Air Trap Assembly Blockage/Obstruction - Technical Service Pointer6 pg
    Covers this model

Tech Tip

  • Instruction Sheet2 pg
    Covers this model
  • Instruction Sheet4 pg
    Covers this model

Quick Reference

  • Quick Reference Manual2 pg
    Covers this model
  • Quick Reference Manual1 pg
    Covers this model

Other

  • Whirlpool FL DD Washer Air Trap Assy Blockage Service Pointer August 2015 W108035286 pg
    Covers this model

Installation Guide

  • Instrucciones de instalacion12 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WFL98HEBU0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (40)

CodeMeaning
12-1No communication between ECM and Appliance Control Unit (ACU)12-2No link between ECM and Wireless Router12-3No link between ECM and Internet12-4Antenna A problem12-5Antenna B problem12-6Current Transformer A problem12-7Provisioning problemF0E1Load detected during the washer cleaning cycle.F1E1Central Control Unit (CCU) errorF1E2Motor Control Unit (MCU) errorF2E2User Interface (UI) software errorF2E3Unsupported cycleF3E1Pressure sensor errorF3E2Temperature sensor errorF3E4Level or presence sensor errorF4E0Heater is not detectedF5E1Door switch errorF5E2Door lock errorF5E3Door unlock errorF6E1Communication error between CCU and Motor Control Unit (MCU)F6E2Communication error from UI to CCUF6E3Communication error from CCU to UIF6E5Communication error between CCU and Expansion Board (EB)F7E1Drive motor speed sensing error / washer overloadF7E2MCU overheat and/or motor overheatF8E0Steam inlet valve errorF8E1No water detected entering washer or pressure sensor trip not detected after 13…F8E2Dispenser system errorF8E3Overflow conditionF8E4Flow meter fault
View all 40 error codes
F9E1Long drainFCE0Communication error, ECM to CCU (model WFL98 only).FCE1Communication error, washer to wireless router (model WFL98 only).FCE2Wireless router cannot communicate with the internet (model WFL98 only).FCE3Antenna A (J2) bad (model WFL98 only).FCE4Antenna B (J11) bad (model WFL98 only).FCE5Current transformer A not functioning (J12) (model WFL98 only).FCE6Current Transformer B problemFCE7Provisioning failureSudSuds detected

Service modes (6)

  • Component Activation["Enter Service Diagnostic Mode.","Navigate to Component Activation on the Diagnostics Home…
  • Component Activation - Dryer["Activate Service Diagnostic Mode","From the Diagnostic Home Screen, select Component…
  • Component Activation - Washer["Activate Service Diagnostic Mode","From the Diagnostic Home Screen, select Component…
  • Quick Diagnostic Test["Enter Service Diagnostic Mode.","Navigate to Error Diagnostic on the Diagnostics Home…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • UI Component Test["Enter Service Diagnostic Mode.","Navigate to Component Activation on the Diagnostics Home…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass