mypros+
Model reference

Whirlpool WTW5105HW2

Washer

10 documents35 error codes7 service modes

Available documentation

Tech Sheet

  • Service Technician Technical Sheet W11427032A2 pg
    Covers this model

Service Manual

  • Whirlpool® and Maytag® 4.7/5.3 Cubic Foot Top Load Washer Technical Manual88 pg
    Covers this model
  • Technical Manual - Whirlpool® and Maytag® 4.7/5.3 Cubic Foot Top Load Washer88 pg
    Covers this model

Service Flash

  • Technical Service Pointer - Grinding Noise in Spin Cycle3 pg
    Covers this model
  • Service Pointer - W11632927 - Rev I - Top Load Washer Will Not Run Cycle and/or GFCI Ground Fault Failure9 pg
    Covers this model
  • Technical Service Pointer #W11750573 Rev. B - Vertical Drain Pump Not Draining8 pg
    Covers this model

Tech Tip

  • Inserts2 pg
    Covers this model

Training

  • Training Manual Service Tool31 pg
    Covers this model

Quick Reference

  • Manual de referencia rápida1 pg
    Covers this model
  • Quick Reference Guide24 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW5105HW2.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (35)

CodeMeaning
F0E2Oversuds condition detected; suds prevent basket from spinning or pressure…F0E3Overload detected; load size exceeds washer capacity or basket cannot be turned.F0E4Spin limited by water temperature; water temperature is too high for final spin…F0E5Off balance load condition detected.F0E7Load detected in basket when running Clean Washer cycle.F0E8Water ring fault; too much residual water detected.F0E9Off balance pause; off balance condition detected after user interventions.F1E1Main control (ACU) fault.F1E2Motor drive module over voltage; main control detects a problem in the motor…F2E1HMI stuck button; user interface detecting a button is continuously activated.F2E2HMI disconnected from the ACU.F3E2Pressure system fault; main control detects an out of range or absent pressure…F3E3Inlet water temperature fault; inlet thermistor detected open or shorted.F3E5Mini bulk system error; bulk level sensor signal detected out of range.F5E1Lid switch faultF5E2Lid lock will not unlock; excessive force on lid, wash media buildup, or main…F5E3Lid lock will not unlock; excessive force or wash media buildup preventing lock…F5E4Lid lock will not lock; obstruction or mechanism failure preventing lid lock…F6E1Lid not opened between cycles; user presses START after predetermined number of…F6E3Communication errorF7E1Tachometer missing or wrong signal; ACU cannot read speed or power from…F7E2MCI drive failure; failure within the motor or ACU hardware.F7E3Basket engaged during wash; shifter is not disengaging the basket for wash mode.F7E4Basket re-engagement failure; shifter not engaging the basket for spin.F7E6Motor circuit open; main control detects one or more motor lines is open.F7E7Motor unable to reach target RPM.F7E8Motor drive module over temperature; main control detects a problem in the…F7E9Locked rotor; motor is not moving when being actively driven.F7EAMotor phase lost; one or more of the three motor phases is lost or under the…F7ECMotor drive module over current/overload.
View all 35 error codes
F8E1Long fill; water level does not change for a period of time or water is present…F8E2Dispenser system failure; bulk pump is on but current is outside thresholds.F8E3Overflow or flood condition; main control senses water level exceeding washer…F8E6Water hazard; main control senses water in tub and lid has been open for more…F9E1Drain pump system problem

Service modes (7)

  • Component Activation["Enter Service Mode.","Navigate to Service Diagnostics.","Select Component Activation."]
  • Diagnostic Cycle["Enter Service Mode.","Navigate to Service Diagnostics.","Select Diagnostic Cycle."]
  • DLMS Calibration Cycle["Enter Service Mode.","Navigate to Factory Diagnostics.","Select DLMS Calibration Cycle."]
  • Fault History["Enter Service Mode.","Navigate to Fault History."]
  • HMI Test["Enter Service Mode.","Navigate to Service Diagnostics.","Select HMI Test."]
  • Sensor Feedback["Enter Service Mode.","Navigate to Service Diagnostics.","Select Sensor Feedback."]
  • Service Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass