mypros+
Error code reference

Whirlpool Washer Error Code F0E7

Load detected when running Clean Washer cycle

Whirlpool codesWhirlpool washer codes

Load detected when running Clean Washer cycle - clothes detected in basket when clean washer cycle is selected.

First step from the service manual

Remove any load from the basket before running clean washer cycle.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F0E7.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F0E7 means on a Whirlpool washer

The F0E7 error code on a Whirlpool washer indicates that the machine has detected a load inside the drum while the Clean Washer cycle is being initiated or run. The Clean Washer cycle is designed to run without any laundry present, using hot water and high agitation or spin speeds to flush out detergent residue, mold, and bacteria from the drum, tub, and internal components. When the washer's load sensing system detects mass or resistance consistent with clothing or other items in the basket, it triggers the F0E7 fault to prevent the cycle from completing under improper conditions.

The load detection system relies on motor current feedback, drum resistance during rotation, or a dedicated load sensor, depending on the specific model. During the Clean Washer cycle startup, the control board monitors these signals and compares them against expected baseline values for an empty drum. If the readings fall outside the acceptable range, the board interprets this as a loaded drum and generates the F0E7 code. This is a protective and procedural fault rather than a component failure, meaning the washer itself is functioning correctly.

The most common cause is simply that clothing or other items were left in the drum before the cycle was selected. However, in some cases, a single heavy item such as a towel or a wet garment stuck to the drum wall can also trigger the fault. If the drum is confirmed empty and the error persists, the issue may point to a faulty load sensing circuit or a control board misreading sensor data.

Source: manufacturer service documentation.

Common causes of F0E7

  1. 01

    Clothing or items left in the drum

    Wiring / connection

    The most frequent cause is laundry, towels, or other items that were not removed before selecting the Clean Washer cycle. Open the door, visually inspect the drum, and remove all contents before restarting.

  2. 02

    Single item stuck to drum wall

    Wiring / connection

    A wet or heavy item such as a towel or sock can cling to the drum interior and be missed during a quick visual check. Run your hand around the entire drum surface, including under the door gasket, to confirm nothing is present.

  3. 03

    Residual water or detergent buildup affecting load sensing

    Wiring / connection

    Excessive detergent residue or standing water in the tub can sometimes interfere with the load sensing system, causing it to register resistance when the drum is empty. Running a Rinse and Spin cycle first to clear the tub may resolve the issue.

  4. 04

    Faulty load sensing circuit or wiring

    Part replacement

    If the drum is confirmed empty and the error continues to appear, the load sensing components or associated wiring harness may be sending incorrect signals to the control board. Inspect wiring connections for corrosion or damage.

  5. 05

    Control board misreading sensor data

    Part replacement

    In rare cases, the main control board may incorrectly interpret sensor inputs and trigger F0E7 even with an empty drum. This would typically only be suspected after all other causes have been ruled out.

See the test procedure for each cause

Frequently asked questions about F0E7

What does F0E7 mean on a Whirlpool washer?
F0E7 means the washer detected a load inside the drum when the Clean Washer cycle was selected. The Clean Washer cycle is designed to run only on an empty drum, so the washer generates this code and stops to alert you. It is a procedural fault, not a mechanical failure, and is resolved in most cases by simply removing items from the drum before restarting the cycle.
How do I fix the F0E7 error on my Whirlpool washer?
Start by opening the door and removing all clothing, towels, or any other items from the drum. Check under and around the door gasket for any small items clinging to the drum wall. Once the drum is fully empty, select the Clean Washer cycle again and the code should not reappear. If the error persists with a confirmed empty drum, the load sensing system or control board may need further diagnosis.
Is it safe to keep using my Whirlpool washer when F0E7 appears?
Yes, F0E7 does not indicate a dangerous condition or a mechanical breakdown. The washer is functioning correctly by refusing to run the Clean Washer cycle with a loaded drum. You can continue using the machine for regular wash cycles without concern. Simply remove the load and retry the Clean Washer cycle when you are ready.
Will resetting my Whirlpool washer clear the F0E7 error?
A reset alone will not permanently clear F0E7 if the root cause, items in the drum, has not been addressed. Unplugging the washer for a minute may temporarily dismiss the code, but it will return when the Clean Washer cycle is attempted again with the drum loaded. The correct fix is to empty the drum first, which resolves the fault at its source.
How much does it cost to repair a Whirlpool washer showing F0E7?
In most cases, the F0E7 error requires no parts or repair costs at all, since it is typically caused by leaving items in the drum before running the Clean Washer cycle. If the error persists with an empty drum and a component such as a load sensor or control board is at fault, repair costs can range from roughly 150 to 400 dollars or more depending on the specific part and labor rates in your area.

Related Whirlpool washer codes

All Whirlpool washer codes
View all 413 Whirlpool washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass