mypros+
Model reference

Whirlpool WTW5550XW3

Washer

16 documents32 error codes15 service modes

Available documentation

Tech Sheet

  • Techsheet W10468342 RevC44 pg
    Covers this model

Service Manual

  • JobAidW10372167L8586 pg
    Covers this model
  • Direct Drive FL Washer86 pg
    Covers this model

Service Flash

  • TECHNICAL SERVICE POINTER - Top Load Washers with Dispenser Drawer6 pg
    Covers this model
  • Technical Service Pointer2 pg
    Covers this model
  • Technical Service Pointer - Service Pointer - 8178818 (Not Spinning)6 pg
    Covers this model
  • Service Pointer - W10411107 (Broken Lid Lock)1 pg
    Covers this model
  • Technical Service Pointer - VMW HE / Hybrid Washers New Plastic Drive Hub6 pg
    Covers this model
  • Service Pointer - W10405379 - Rev A (Elimination of Counter Weight)1 pg
    Covers this model
  • Technical Service Pointer - Continuous Test Mode3 pg
    Covers this model
  • Technical Service Pointer #W10492393 - Drive (Splutch) Pulley Comes Loose6 pg
    Covers this model

Tech Tip

  • Service Pointer - W10657326 (Customer Tip Sheet)3 pg
    Covers this model

Training

  • Training Pointer - 8178817 (Washer not Filling at Cycle)3 pg
    Covers this model
  • Technical Training Pointer - VMW HE / Hybrid Washers New Plastic Drive Hub6 pg
    Covers this model

Quick Reference

  • Quick Reference Manual2 pg
    Covers this model
  • Manual de referencia rapida1 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WTW5550XW3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (32)

CodeMeaning
F0E1Load detected during the washer cleaning cycleF0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected during rinse cycle (105°F or higher).F0E5Off balance load detected.F1E1CCU errorF1E2MCU errorF2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Unsupported cycleF3E1Pressure switch/pressure sensor errorF3E2Temperature sensor errorF5E1Door switch errorF5E2Door lock errorF5E3Door unlock errorF5E4Lid not opened between cycles; user presses START after several consecutive…F6E1Communication error between CCU and MCUF6E2Communication error UI to CCUF6E3Communication error CCU to UIF7E1Drive motor tachometer error / washer overloadF7E2MCU fault or motor overheatF7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E0Steam inlet valve errorF8E1No water detected entering washer or pressure switch trip not detectedF8E2Dispenser system errorF8E3Overflow conditionF8E4Flow meter faultF8E5Hot and cold inlet hoses are reversed.F9E1Long drainIntInterrupted
View all 32 error codes
rLRemove loadSudSuds detected

Service modes (15)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' LED is On (or '02'…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' LED is On (or '04'…
  • Clear Fault Codes1
  • Fault Code DisplayFrom Service Diagnostic Mode, press and release the 3rd button used to activate Service Diagnostic…
  • Fault Code Display / Advance1
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Done' LED is On (or '01'…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin & Done' LEDs are On…
  • Quick Diagnostics1
  • Service Diagnostic Mode1. Ensure washer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display1
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse, Spin, and Done'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are On…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse & Spin' LEDs are On…
  • User Interface Test1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass