mypros+
Error code reference

Amana Oven Error Code F3-1

Sensor or sensor circuit failure.

Amana codesAmana oven codes

Sensor or sensor circuit failure.

First step from the service manual

Check wire connections and sensor.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F3-1.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F3-1 means on a Amana oven

The F3-1 error code on an Amana oven indicates a failure in the oven temperature sensor or its associated wiring circuit. The temperature sensor, typically a resistance temperature detector (RTD) probe, monitors the oven cavity temperature and sends a continuous resistance signal to the control board. At room temperature, a properly functioning RTD sensor generally reads around 1080 to 1100 ohms. When the control board detects a resistance value outside its expected range, whether too high, too low, or an open/short circuit condition, it triggers the F3-1 fault code and halts normal oven operation.

The most common causes of this fault fall into two categories: physical sensor failure and wiring circuit problems. The sensor probe itself can degrade over time due to repeated thermal cycling, leading to an open circuit or a drifting resistance value. Equally common are failures in the wiring harness that connects the sensor to the control board, including loose connectors, corroded terminals, or wires that have been damaged by heat exposure near the oven cavity.

Diagnosing this code should begin with a visual inspection of all wire connections between the sensor and the control board, followed by an ohmmeter reading taken directly at the sensor probe terminals. If the sensor reads outside the expected resistance range or shows an open circuit, the sensor requires replacement. If the wiring and sensor both check out, the control board itself may be misreading the sensor signal and could be the source of the fault.

Source: manufacturer service documentation.

Common causes of F3-1

  1. 01

    Failed oven temperature sensor (RTD probe)

    Part replacement

    The RTD sensor probe degrades over time and can develop an open circuit or incorrect resistance reading. Testing the sensor with an ohmmeter at its connector terminals will confirm failure if the reading is significantly outside the expected range near 1080 to 1100 ohms at room temperature.

  2. 02

    Loose or disconnected wiring at the sensor connector

    Wiring / connection

    Vibration and heat cycling can cause the sensor connector to loosen or pull away from the sensor terminals. Inspecting and reseating the connector at both the sensor and control board ends is the first physical check to perform.

  3. 03

    Damaged or shorted wiring harness

    Part replacement

    Wires routed near the oven cavity can become brittle, cracked, or pinched over time, causing a short or open condition in the sensor circuit. A visual inspection along the full length of the harness and a continuity test will identify breaks or shorts.

  4. 04

    Corroded sensor or harness terminals

    Wiring / connection

    Moisture and grease exposure can cause corrosion on the connector terminals, increasing resistance in the circuit and producing a false fault reading. Corroded terminals may require cleaning or connector replacement to restore a proper signal.

  5. 05

    Faulty electronic control board

    Part replacement

    If the sensor and all wiring test within normal specifications, the control board may be misinterpreting the sensor signal due to an internal component failure. This is the least common cause and should only be considered after the sensor and wiring have been ruled out.

See the test procedure for each cause

Frequently asked questions about F3-1

What does F3-1 mean on a Amana oven?
F3-1 on an Amana oven indicates a sensor or sensor circuit failure in the oven temperature monitoring system. The control board is receiving a signal from the RTD temperature sensor probe that falls outside the acceptable resistance range. This prevents the oven from operating safely and accurately. The fault points to either a failed sensor probe, a wiring issue, or in rarer cases, a faulty control board.
Can I fix an F3-1 error on my Amana oven myself?
Yes, a DIYer with basic electrical skills can often resolve this fault. Start by unplugging the oven and inspecting the sensor wiring connections for looseness or visible damage. Use an ohmmeter to test the sensor probe resistance and compare it to the expected value around 1080 to 1100 ohms at room temperature. If the sensor reads open or far outside that range, replacing the sensor probe is a straightforward repair.
Is it safe to use my Amana oven while F3-1 is displayed?
No, you should not use the oven while the F3-1 code is active. The fault means the oven cannot reliably monitor its internal temperature, which creates a risk of overheating or uneven cooking. The oven's control board will typically disable heating functions when this fault is detected, and attempting to bypass it is not recommended.
Will resetting my Amana oven clear the F3-1 error code?
A reset, performed by unplugging the oven for a few minutes and restoring power, may temporarily clear the display, but the code will return if the underlying sensor or wiring problem is not corrected. A reset is useful as a first step to rule out a temporary control glitch, but a persistent F3-1 code requires physical diagnosis and likely a component repair.
How much does it cost to repair an F3-1 error on an Amana oven?
If only the temperature sensor probe needs replacement, parts typically range from around $20 to $60 depending on the specific model, and the repair is relatively simple. If the wiring harness requires repair or replacement, costs can rise into the $50 to $150 range for parts and additional labor. A control board replacement represents the most expensive scenario, with parts often ranging from $100 to $300 or more, making professional diagnosis worthwhile before committing to that repair.

Related Amana oven codes

All Amana oven codes
View all 33 Amana oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass