Skip to main content
Error code reference
Amana Oven Error Codes
81 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
10No line frequency input detected.20RTD (temperature sensor) open circuit detected.21RTD (temperature sensor) Shorted30EEprom memory error.31Invalid model number detected.40Line voltage too Low41Line voltage too High50High current detected.60Stuck keypad detected.C10No line frequency input detected.CHECK SHIELDShield switches are not properly engaged, possibly due to shields being out of place or…doorLock status is not sensed within 60 seconds of energizing the door lock relay (one full…F0Default F codeF0-0No errorF0-E0Default code indicating no fault present.F01Temperature probe errorF02Temperature errorF03EEPROM errorF04WIDE communication errorF05Latch error (pyro version only)F06Door error (pyro version only)F07Cooking parameter data set errorF08User Interface (UI) EEPROM errorF09UI SPI memory errorF1Control malfunction-may be caused by latch switch, door frame switch, or door motor…F1-3Over temperature while cleaning.F1-5Cancel key input out of range.F1-7Keyboard disconnected.F1-8Shorted key.F1-9Slave micro not functioning.F1-AVCC/GND lift off.F1-CControl not calibrated.F1-EEEPROM data corruption.F1-E0Key held down too long, or key is shorted.F1-E1Electronic control module failure.F1-E3Fuel type (gas/electric) select failure.F1-E4Electronic control module failure.F1-E5Electronic control malfunction (keypad related).F1-E6CANCEL key drive line open.F1-E7Circuit board thermistor open or short-circuited.F1-E9WIDE queue full.F1-FIncorrect project number in EEPROM.F1-HDoor switch input circuit failure.F1-JLatch switch input circuit failure.F116th sense error, voltage error, or current errorF1E2A/D error(s)F2Shorted key (keypad short circuit). LCC 180/190 variantF2-E0Temperature sensor opened (R=2875 ohms by spec).F2-E1Temperature sensor shorted (R=825 ohms by spec).F2-E2Prolonged key press or short circuit on keypad.F2-E5CANCEL key drive line open.F2-E6Electronic control malfunction (associated with keypad/cancel key).F20FPGA errorF21HMI input errorF3Oven sensor open circuit, oven sensor short circuit, bake/broil excessive temperature, or…F3-1Sensor or sensor circuit failure.F3-E0Temperature sensor opened (R=2875 ohm by spec).F3-E1Temperature sensor shorted (R=825 ohm by spec).F3-E2Oven temp too highF3-E3Oven temp too highF4Shorted sensor or sensor circuit (resistance <500 ohms).F4-E0Meat probe malfunctionF4-E1Door is open but latch is locked (door switch indicates open door and latch switch…F5Door and switch mismatch during clean mode, or door latch not functioning during clean…F5-E0Door is open, but latch is locked (condition exists when door switch is closed indicating…F5-E1Self-clean latch will not lock or will not unlock.F5E2Door and switch mismatch (clean mode).F6-E0Excessive temperature in lower cavity during bake mode.F6-E1Excessive temperature in microwave oven during cooking.F6-E3Warming drawer over-temperature condition.F7Shorted input key (touch pad malfunction).F8-E0Self-clean latch unable to unlock.F8-E1Self-clean latch unable to unlock.F8-E2Excessive temperature in oven with door open and latch locked.F8-E3Excessive temperature in oven with door open and latch unlocked.F8-E4Excessive temperature in oven with door closed and latch unlocked.F9Defective house wiring or defective range wiring. LCC 180/190 variantF9-1Auto latch will not lock.F9-2Auto latch will not unlock.F9-E0Incorrect home or range wiring.FFDoor lock or door lock circuitry malfunction (door locked).
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.