Skip to main content
Error code reference
Amana Range Error Codes
128 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
1c1cShorted key detected; disables audible feedback for key depression and disables the…1c2cKeyboard queue disconnected1c31Cancel key circuit problem1c32Cancel key circuit problem1c4cMicro communication failure (serial communications checksum invalid); disables all…1c5cVcc or ground fault at test point; disables all outputs.1c6cEEPROM error, no response from EEPROM; no action taken by control.1c7cControl not calibrated; calibration value out of range; disables all outputs.1c81EEPROM CRC error in upper cavity cook profile data.1c8cCooking program error1d11Temperature sensor resistance greater than 2237 ohms (sensor open/high resistance)1d12Runaway oven temperature (650°F) with door unlocked; sensor resistance > 2237 Ohms.1d21Runaway temperature (510°C / 950°F) with door locked1d22Runaway oven temperature (950°F) with door locked; sensor resistance > 2787 Ohms.20RTD (temperature sensor) Open.21RTD (temperature sensor) Shorted.30EEprom memory error.3d11Oven temperature sensor open (sensor resistance is infinite); disables all cook functions…3d12Sensor open (H1 control, second cavity)3d21Oven temperature sensor shorted (sensor resistance is 0 Ohms); disables all cook…3d22Sensor shorted (H1 control, second cavity)3d41Meat probe shorted during active probe cook mode.3d51Meat probe not calibrated; detected during active probe cook mode.40Line voltage too Low.41Line voltage too High.4d11Door position switch failure4d12Door position switch failure4d21No reverse airflow fan rotation detected (no or low RPM) during cook or clean (H1 control…4d31Cooling fan is running when it should be de-energized (idle state).4d41Cooling fan overspeed detected during active cook or clean mode.4d51Door switch circuit failure4d52Door switch circuit failure60Stuck keypad.9d11Latch will not lock (lock switch not closed when clean activated); ignores soil level…9d12Door latch will not lock; lock switch not closed when it should be.9d21Latch will not unlock (lock switch closed when clean not activated); disables cooking…9d22Door latch will not unlock; unlock switch not closed when it should be.9d31Unknown lock state9d32Latch state unknown; both locked and unlocked switches indicate active simultaneously.9d41Unlock state unknownC10No line frequency input detected.CLrNo error(s) found; no corrective action required.DOORDisplayed in Bake or Broil mode indicating a defective latch switch, shorted wire lead…E0 F1EEPROM communications failure, typically caused by power line noise or lightning.E0 F3Key contact closed for more than 60 secondsE0 F3 (sensor open)Break in oven sensor circuitE0 F5Door switch open during cleanE1 F2EEPROM checksum failure, typically caused by power line noise or lightning.E1 F3No communication between keyboard and controlE1 F3 (sensor short)Short in oven sensor circuitE1 F5Door latch not operatingE2 F3Bake/Broil temperature out of range (too high)E3 F3Clean temperature out of range (too high)F0Loss of safety signalF0-0No errorF0E0No failure present (displays only if user presses and holds CANCEL/OFF key for 5 seconds…F1A shorted key (button) detected for 32 seconds in a row, indicating a stuck or binding…F1 E3Fuel type (gas/electric) select failure.F1-1Over temperature while cooking.F1-3Over temperature while cleaning.F1-4Over temperature while cooking.F1-5Cancel key input out of range.F1-7Keyboard disconnected.F1-8Shorted key.F1-9Slave micro not functioning.F1-AVCC/GND fift off.F1-CControl not calibrated.F1-EEEPROM data corruption.F1-E0EEPROM communications failure, possibly caused by power line noise or lightning.F1-E1EEPROM checksum failure, possibly caused by power line noise or lightning.F1-E5Sensor usage out of range (internal).F1-E7PCB Thermistor/Sensor open or shorted.F1-FIncorrect project number in EEPROM.F1-HDoor switch input circuit failure.F1-JLatch switch input circuit failure.F1E2Internal error (display board related).F1E4Internal error (display board related).F1E6Internal error (power board related).F1E8Internal error (power board related).F1E9Internal error (display board related).F2Excessive oven temperature, or sensor resistance too high (ERC III).F2 E6Cancel key failure.F2-E0Key contact closed for more than 60 seconds due to key held down too long, shorted key…F2-E1No communication between keyboard and control due to keytail being loose, unplugged, or…F2-E2Stuck key detected.F26Oven temperature runaway.F3An open circuit in the sensor wire harness, or sensor resistance too high (ERC III Auto…F3-1Sensor or sensor circuit failure.F3-E0Break (open) in oven sensor circuit due to open sensor, loosened/disconnected sensor…F3-E1Short in oven sensor circuit due to shorted sensor, sensor shorted to casing…F3-E2BAKE/BROIL temperature out of range (too high)-BAKE or BROIL elements do not turn off.F3-E3Clean temperature out of range (too high)-BAKE element does not turn off during clean…F30RTD is open.F3E4Bottom oven temperature sensor open (bottom oven sensor open).F3E5Bottom oven temperature sensor shorted (lower oven sensor shorted).F3E6Warming drawer temperature sensor open.F3E7Warming drawer temperature sensor shorted.F4Sensor resistance too low (below 500 ohms), indicating possible short in sensor wire…F4-CControl not calibrated.F4E2Over temperature during cook mode.F4E3Over temperature during clean mode.F4E7Over temperature cavity 2 (temperature runaway error).F5Door and switches do not agreeF5-E0Door switch open during clean cycle due to switch failing open, open or loose wire…F5-E1Latch switch not operating-latch switch does not close in clean (contacts stay open)…F5-E2Latch error during CLEAN cycle.F5E4Latch switch fault.F5E7Unlock door errorF6Indicates a failed component in the ERC or caused by fluctuations in 60 Hz power source.F6-E0Lost communications.F6-E1Over temperature during cook mode (runaway temp).F6-E2Over temperature during clean mode (runaway temp).F6-E3Over temperature in warming drawer (runaway temp).F6E4Lost communication between power board and display board.F6E5Cancel key error.F7Indicates a shorted or sticking contact in one or more of the function control switches.F8Indicates a failed component in the ERC.F9Door Latch Supervisory failureF9-1Auto latch will not lock.F9-2Auto latch will not unlock.F9-E0Product is mis-wired.F90Door lock in wrong position.F93Invalid lock/unlock inputs detected.FFOven temperature is above 585°F and door circuitry has a problem after 16 seconds.FFFControl failure detected in the KRC electronic range control.FQ-0No errorGoodNo failure present; displayed only when user enters diagnostic mode and there are no…LOCKIf 'LOCK' appears in the display when the oven is not set in clean mode, it indicates a…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.