mypros+
Error code reference

ASKO Dryer Error Code Thermistor

The thermistor may have become disconnected or have an internal fault, causing potential temperature regulation failure.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Thermistor error code actually means

Your Asko dryer has detected a problem with the temperature sensor, which normally tells the dryer how hot the air inside is getting. Without accurate temperature readings, the dryer cannot control its heat properly, so it has stopped as a safety precaution. The sensor may have come loose from its connector or may have worn out and needs to be replaced.

Diagnostic procedure

The full Thermistor procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check thermistor resistance (should be 40-60 kΩ at 68°F-86°F / 20°C-30°C); verify it is properly installed in the fan housing.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Thermistor procedure $9.95

Or subscribe: $29/month for all codes plus Max AI diagnostics, with 70 Max messages a day.

Most common causes of Thermistor

Ranked by how often they cause this code
  1. 1Disconnected thermistor connector
  2. 2Failed thermistor (out-of-range resistance)
  3. 3Damaged wiring harness
  4. 4Lint or debris around the thermistor
  5. 5Faulty control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Thermistor

What does Thermistor mean on a Asko dryer?
This error means the dryer's temperature sensor has either become disconnected or has developed an internal fault. The thermistor, located in the fan housing, is responsible for monitoring air temperature during the drying cycle and reporting it to the control board. When the control board cannot get a valid reading from the thermistor, it stops the dryer to prevent unsafe operation. Diagnosis starts with checking the sensor's resistance, which should fall between 40 and 60 kΩ at room temperature.
Is it safe to keep using my Asko dryer when the Thermistor error appears?
No, you should not continue running the dryer with this error active. The thermistor is what allows the control board to regulate heat, and without valid temperature data, the dryer cannot prevent overheating. Continuing to use the appliance could pose a fire risk or cause damage to other components. Resolve the error before resuming normal use.
How much does it cost to repair a Thermistor error on an Asko dryer?
If the fix is simply reseating a loose connector, there is no parts cost involved. A replacement thermistor part typically falls in the range of $20 to $60 depending on the specific model. If professional labor is needed, total repair costs including parts and service can range from $100 to $250. A control board replacement, if required, would be at the higher end of the repair cost spectrum.
Can I fix the Thermistor error myself on my Asko dryer?
A knowledgeable DIYer with a multimeter can often resolve this error by checking the thermistor resistance and reseating the connector in the fan housing. If the resistance reading is outside the 40 to 60 kΩ range at 68°F to 86°F, the thermistor itself needs replacement, which requires purchasing the correct part and accessing the fan housing interior. If wiring or the control board is involved, professional repair is recommended.
Will resetting my Asko dryer clear the Thermistor error?
A reset may temporarily clear the error code, but it will return if the underlying problem with the thermistor or its wiring has not been corrected. The control board will detect the out-of-range or missing signal again as soon as a drying cycle begins. A lasting fix requires diagnosing and repairing the sensor, its connector, or the associated wiring.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass