Error code reference
ASKO Washer Error Code F30
Maximum programme time exceeded during appliance operation.
Maximum programme time exceeded during appliance operation.
MyPros+ Max
Get the full diagnostic procedure for F30.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·ASKO Washer
F30 on my ASKO Washer
M+
Maximum programme time exceeded during
From Service Manual 491065, p.37:
1.Access service mode to confirm the active fault code and read stored error history.
2.Measure control board supply voltage at the test points. Expected: 12 VDC and 5 VDC; a drop below 4.75 VDC on the logic rail points to a failed onboard regulator.
3.Inspect all connectors on the main control for corrosion, thermal stress, or backed-out pins. Reseat each connector with the power disconnected.
Part WPW10804018
Electronic control board
Related ASKO washer codes
All ASKO washer codes →- 0000Flashing 0000 in the top right corner of the display…
- CCheck step
- Door lockIndicated when the circuit control for the door lock is…
- Door lock faultA fault has been detected with the door lock mechanism.
- drain errorIf the drain pump has run for 180 seconds during draining…
- Draining faultDraining has taken too long; drain pump ran for 180 seconds…
- EDrain pump error
- E1Water level detection error
View all 66 ASKO washer codes
- E2Error code that appears on the display if the drain pump…
- E4Water leakage during washing
- E5DC-Link high voltage error
- E6Error code logged in the PCB; specific details not provided…
- E7Direction error
- E8Initial Operation Fail Error
- E9Abnormalities in water level sensor
- Engine faultNo signal from Tacho or MCU.
- F1Over flow
- F10Overflow
- F11Water outlet fault
- F12Water inlet fault
- F2Wash motor fault
- F20Door opening fault during appliance operation.
- F29Clean HP (high-pressure) filter required during appliance…
- F3Thermistor fault
- F31NTC1 temperature sensor missing during appliance operation.
- F4Temperature stop fault
- F5Foaming detected
- F6Temperature stop fault
- F7Foaming detected
- F8Control card fault
- F9The machine has not spun
- Foam checkIndicated after the program has finished; the machine has…
- FoamingThe water level has not decreased to a certain level during…
- H2Washing temperature sensor open/short
- H4Washing temperature sensor overheating
- H5Water temperature error in wool/delicate course
- H6Abnormality in washing heater
- H8Washing heater overheating
- IEInput Error
- LELock Error
- Motor faultWiring open-circuit or motor fault has been indicated and…
- OEOutput Error
- Over flow faultToo much water in the machine, or the drain pump is running…
- OverfillingToo much water in the drum due to a fault in the level…
- OverflowW640/W660 display indicating too much water in the drum due…
- PFEPump filter error
- Pressour sensor faultIndicated if the water level drops to 0 within 30 seconds…
- Pressure faultIndicated if the water level drops to zero within 30…
- Pressure sensorWater level is decreasing and drops to zero level within 15…
- Pressure sensor faultA drop in pressure has been detected in the first rinse…
- SSafety step
- Security faultThe door is open during operation.
- SensorThe control signal from the rinse sensor is missing.
- Temperature faultThe temperature has increased less than 5°C in ten minutes…
- Temperature stopTemperature setting has not been reached within 25 minutes…
- Temperature stop faultHeating failure detected; check the fuses and the heating…
- ThermistorW640/W660 display indicating the washing program finished…
- Thermistor faultThe circuit for the thermistor is open, the thermistor is…
- UEUnbalance Error
- UnbalanceAfter 10 failed attempts to spin, the machine has stopped…
- Wash motorWiring open-circuit or motor fault has been indicated and…
- Wash motor faultNo signal from the tacho or MCU.
- Water inletW640/W660 display indicating a fault in the water supply.
- Water inlet faultWater inlet fault detected during program cycle on…
- Water outletW640/W660 display indicating draining has taken too long.
- Water outlet faultThe drain pump has been activated for more than 3 minutes…
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass