Skip to main content
Error code reference
ASKO Washer Error Codes
72 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
0000Flashing display indicating the machine has detected an imbalance; the built-in imbalance…CCheck stepDoor lockIndicated when the circuit control for the door lock is broken.Door lock faultA fault has been detected with the door lock mechanism.drain errorIf the drain pump has run for 180 seconds during draining without completing, the program…Draining faultDraining has taken too long; drain pump ran for 180 seconds during emptying and the…EDrain pump errorE1Water level detection errorE2Error code that appears on the display if the drain pump has run for 180 seconds during…E4Water leakage during washingE5DC-Link high voltage errorE6EMG errorE7Direction errorE8Motor operation errorE9Abnormalities in water level sensorEngine faultNo signal from Tacho or MCU.F1Over flow-The sensor receives the first signal that overflow has taken place, e.gF10OverflowF11Water outlet faultF12Water inlet faultF2Wash motor fault caused by interruption in cables to the motor, a faulty motor capacitor…F20Door opening fault during appliance operation.F29Clean HP (high-pressure) filter required during appliance operation.F3Thermistor fault-the machine indicates whether there is an interruption or short-circuit…F30Maximum programme time exceeded during appliance operation.F31NTC1 temperature sensor missing during appliance operation.F4Temperature stop fault-indicates whether the temperature is not reached within 80 minutes…F5Foaming detected-foaming is checked after the main wash (this function is not provided on…F6Temperature stop fault indicating the wash temperature is not reached within 80 minutes…F7Foaming detected-foaming is checked after the main wash and the fault indication appears…F8Control card fault-A fault has occurred on the control card, which must be replaced to…F9The machine has not spun-the built-in imbalance sensor caused the speed to be reduced or…Foam checkIndicated after the program has finished; the machine has detected via the level sensor…FoamingThe water level has not decreased to a certain level during the first outlet after main…H2Washing temperature sensor open/shortH4Washing temperature sensor overheatingH5Water temperature error in wool/delicate courseH6Abnormality in washing heaterH8Washing heater overheatingIEInput ErrorL1Over fillingL2Door open faultL3Drainage faultL4Fault with water supplyL5Door opening faultLELock ErrorMotor faultWiring open-circuit or motor fault has been indicated and the washing program has been…OEOutput ErrorOver flow faultToo much water in the machine, or the drain pump is running without any water in the…OverfillingToo much water in the drum due to a fault in the level sensing system or the inlet valve…OverflowW640/W660 display indicating too much water in the drum due to a fault in the level…PFEPump filter errorPressour sensor faultIndicated if the water level drops to 0 within 30 seconds of the first rinsing.Pressure faultIndicated if the water level drops to zero within 30 seconds of the first rinse.Pressure sensorWater level is decreasing and drops to zero level within 15 seconds in the first rinse.Pressure sensor faultA drop in pressure has been detected in the first rinse, possibly due to leakage in the…SSafety stepSecurity faultThe door is open during operation.SensorThe control signal from the rinse sensor is missing.Temperature faultThe temperature has increased less than 5°C in ten minutes; the wash cycle continues to…Temperature stopTemperature setting has not been reached within 25 minutes for wool wash cycle or 80…Temperature stop faultHeating failure detected; check the fuses and the heating elementThermistorW640/W660 display indicating the washing program finished without heating because the…Thermistor faultThe circuit for the thermistor is open, the thermistor is faulty, or the measurement…UEUnbalance ErrorUnbalanceAfter 10 failed attempts to spin, the machine has stopped spinning because of too high…Wash motorWiring open-circuit or motor fault has been indicated and the washing program has been…Wash motor faultNo signal from the tacho or MCU.Water inletW640/W660 display indicating a fault in the water supply.Water inlet faultWater inlet fault detected during program cycle on W640/W650/W660Water outletW640/W660 display indicating draining has taken too long.Water outlet faultThe drain pump has been activated for more than 3 minutes and water remains in the…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.