mypros+
Error code reference

ASKO Washer Error Code F4

Temperature stop fault-indicates whether the temperature is not reached within 80 minutes (30 minutes for wool and hand wash).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F4 error code actually means

Your Asko washer is showing an F4 error because it could not heat the water to the right temperature in time. This usually points to a problem with the internal water heater or the sensor that measures water temperature. The washer stopped the cycle to prevent damage and to let you know something needs attention.

Diagnostic procedure

The full F4 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F4 procedure $9.95

Or subscribe: $29/month for all codes plus Max AI diagnostics, with 70 Max messages a day.

Most common causes of F4

Ranked by how often they cause this code
  1. 1Failed heating element
  2. 2Faulty NTC temperature sensor
  3. 3Wiring or connector fault in the heating circuit
  4. 4Failed heating relay on the control board
  5. 5Very low incoming water temperature or low mains voltage

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F4

What does F4 mean on a Asko washer?
The F4 code on an Asko washer indicates a temperature stop fault. It means the washer was unable to heat the water to the required temperature within the allowed time, which is 80 minutes for standard cycles and 30 minutes for wool and hand wash programs. The machine stops the cycle and displays the code to alert you to a problem in the heating system.
Is it safe to continue using my washer when the F4 code is displayed?
You should not continue running cycles while the F4 fault is active. The washer has already stopped the cycle because the heating system is not functioning correctly. Running laundry in a machine with an unresolved heating fault risks incomplete washing and could mask a wiring or electrical issue that warrants proper diagnosis before further use.
How much does it typically cost to repair an F4 error on an Asko washer?
Repair costs vary depending on which component has failed. A heating element replacement typically falls in the range of $100 to $250 including parts and labor, while an NTC sensor is generally a less expensive repair. Control board replacement is the most costly possibility, often ranging from $200 to $450 or more depending on the model and service rates in your area. Getting a diagnostic visit from a technician will pinpoint the exact part needed before committing to a repair cost.
Can I fix the F4 error myself, or do I need a technician?
Some causes of F4 are accessible to a knowledgeable DIYer, such as checking wiring connections or testing the heating element and NTC sensor with a multimeter. However, replacing internal components like the heating element or control board requires disassembly and electrical work, so comfort with appliance repair is important. If you are not confident working with internal electrical components, calling a qualified technician is the safer choice.
Will resetting the washer clear the F4 error code?
A reset may temporarily clear the F4 display, but if the underlying cause has not been repaired, the code will return during the next cycle that requires heating. Resetting is useful to confirm whether the fault was a one-time occurrence, such as an unusually cold water supply on a winter day, but a recurring F4 indicates a component failure that needs to be diagnosed and repaired.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass