Model reference

ASKO WM66A

Name: ASKO WM66A
Brand: ASKO

Washer

6 documents13 error codes21 service modes

Available documentation

Service Manual

Service manual Type: WM55A/66A15 pg
Covers this model
Service manual Type: WM50 Front-loading11 pg
Covers this model
Service manual Type: WM50 Front-loading washing machine11 pg
Covers this model
Service manual Type: WM5011 pg
Covers this model
Service manual Type: WM33A WM44A8 pg
Covers this model
Service manual Type: WM55A/66A Front-loading15 pg
Covers this model

MyPros+ Max

Diagnose your ASKO WM66A.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·ASKO Washer

drain error on my ASKO WM66A

M+

If the drain pump has run for 180

From Service Manual 141087, p.19:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drain pump winding resistance at connector J7. Expected: 12 to 16 ohms at room temperature.

3.Verify the board switches the pump at 120 VAC during the drain cycle.

Part W10876537

Drain pump assembly

Error codes (13)

CodeMeaning

drain errorIf the drain pump has run for 180 seconds during draining without completing…EDrain pump error E2Error code that appears on the display if the drain pump has run for 180…F1Overflow detected F10Door opening fault F2Wash motor fault F3Draining fault F4Water inlet fault F5Thermistor fault F6Temperature stop fault F7Foaming detected F8Control card fault F9The machine has not spun

Service modes (21)

Celsius/Fahrenheit reprogrammingProgram knob in 0 position
Change Celsius to Fahrenheit["Ensure programs are in 0 position.","Press 5x Enter + 5x P2.","Change setting with < or > arrow…
Change Language["Ensure programs are in 0 position.","Press 5x Enter + 5x P1.","Change language with < or > arrow…
Child-safe Start and Menu Setting["Ensure programs are in 0 position.","Press 5x Enter + 5x P3.","Change setting with < or >, 0 or 3…
Child-safe Start settingProgram knob in 0 position
Reprogramming - Celsius to FahrenheitProgram knob in 0 position
Reprogramming - Change Celsius to Fahrenheit["Ensure programs are in 0 position.","Press Enter 5 times, then press P2 5 times.","Change setting…
Reprogramming - Change language["Ensure programs are in 0 position.","Press Enter 5 times, then press P1 5 times.","Change…
Reprogramming - Child-safe StartProgram knob in 0 position
Reprogramming - Child-safe Start and Menu["Ensure programs are in 0 position.","Press Enter 5 times, then press P3 5 times.","Change setting…
Reprogramming - Spin speed settingProgram knob in 0 position. Hold down the Start button and press Super rinse 5 times. Release the…
Reprogramming - Water intake settingProgram knob in 0 position
Reset program["Hold down the current program button (P1-P4).","Press Enter."]
Reset WM66A sensor["Press Menu 5 times, then press key, then press Start."]
Shop Program["Switch the machine off and on with the main switch.","Press 5x Start/Stop + S8 + S7 + S6 + S5 +…
Shop program activation["Switch the machine off and on with the main switch.","Within 14 seconds, press
Spin speed settingProgram knob in 0 position. Hold down the Start button and press Super Rinse 5 times. Release the…
Test program - Level 1 (Component activation)Hold down the Start/Stop button and at the same time press S5 five times within 15 seconds to start…
Test program - Level 2 (Component activation)After entering Level 1, press S6 once to reach Level 2.
Test program / faultfinding["Switch the machine off and on with the main switch.","Press S5 five times, OR short-circuit via…
Water intake settingProgram knob in 0 position

Full entry steps, exit procedures, and test sequences are available in Max.

Related ASKO washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass