mypros+
Error code reference

GE Dryer Error Code Door Switch Stuck Open

Dryer did not detect the door was closed within 5 minutes of displaying 'Please close the door', or 3+ consecutive cycles started without detecting…

GE codesGE dryer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Door Switch Stuck Open error code actually means

Your GE dryer's control system couldn't confirm that the door was properly closed, either because it waited too long for a door-close signal or because it noticed the door never seemed to open between multiple cycles. This usually points to a faulty door switch, a loose wire connection, or a problem with one of the control boards. The dryer will not run normally until the issue is identified and resolved.

Diagnostic procedure

The full Door Switch Stuck Open procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check wiring connections, door switch, or inverter board
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Door Switch Stuck Open procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Door Switch Stuck Open

Ranked by how often they cause this code
  1. 1Faulty Door Switch
  2. 2Loose or Damaged Wiring Connections
  3. 3Door Striker or Latch Misalignment
  4. 4Inverter Board Failure
  5. 5Repeated Cycle Starts Without Door Opening

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Door Switch Stuck Open

What does Door Switch Stuck Open mean on a GE dryer?
This error means the GE dryer's control system could not confirm the door was closed. It activates either when the dryer waits more than 5 minutes for a door-close signal after prompting the user, or when three or more consecutive cycles are started without the door ever being detected as opened between them. The problem typically involves the door switch, its wiring, or the inverter board.
Is it safe to use my GE dryer when this error appears?
The dryer will typically not operate normally while this error is active, which is the control system's way of preventing unsafe operation without confirmed door status. You should not attempt to bypass the door switch, as the door switch is part of the dryer's safety circuit. Resolve the underlying fault before resuming normal use.
Will resetting my GE dryer clear the Door Switch Stuck Open error?
A power reset may temporarily clear the error code, but if the underlying cause such as a faulty switch, broken wire, or board issue is still present, the error will return. If the error was triggered only by repeated restarts without opening the door, simply opening the door and allowing a normal cycle start may resolve it. Persistent errors require proper diagnosis and repair of the root cause.
Can I fix the Door Switch Stuck Open error myself?
Many cases of this error can be resolved with basic DIY repair. Start by checking that the door closes firmly and that the striker makes solid contact with the switch. Inspect wiring connections at the switch and inverter board for anything loose or corroded. If the switch fails a continuity test, replacing it is a straightforward repair for most technicians and experienced DIYers.
How much does it cost to repair the Door Switch Stuck Open error on a GE dryer?
If the door switch itself is the problem, replacement parts generally cost between $10 and $40 depending on the model, and the repair is relatively inexpensive if done without a service call. If the inverter board is at fault, board replacement can range from $100 to $250 or more for parts alone. Professional labor charges will add to these estimates depending on your location and the technician's rates.

Related GE dryer error codes

All GE dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass