mypros+
Error code reference

GE Refrigerator Error Code 0314

Convertible drawer freezing when set to warm.

GE codesGE refrigerator codes

Convertible drawer freezing when set to warm.

MyPros+ Max

Get the full diagnostic procedure for 0314.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0314 means on a GE refrigerator

Error code 0314 on a GE refrigerator indicates that the convertible drawer is reaching freezing temperatures even when the drawer has been set to a warmer temperature zone. The convertible drawer is designed to switch between refrigerator and freezer modes, allowing users to store items at different temperatures depending on their needs. When the control system detects that the drawer temperature is dropping below the expected range for the selected warm setting, it logs this fault to alert the technician or user that temperature regulation in that zone has failed.

The root cause is typically a failure in the component or control circuit responsible for modulating cold air delivery to the convertible drawer. This can involve a stuck or faulty damper that is allowing excess cold air to flow into the drawer continuously, a defective thermistor that is sending incorrect temperature readings to the control board, or a control board that is misinterpreting the drawer's target temperature setting. In any of these scenarios, the drawer receives more cooling than intended, causing food stored in warm mode to freeze.

Proper diagnosis requires verifying the drawer's actual temperature with a calibrated thermometer, inspecting the damper assembly for mechanical binding or electrical failure, and checking the thermistor resistance against specification. The main control board should also be evaluated if the damper and thermistor check out correctly, since incorrect output signals from the board can cause this exact symptom regardless of the sensor or actuator condition.

Source: manufacturer service documentation.

Common causes of 0314

  1. 01

    Stuck or failed damper assembly

    Part replacement

    The damper controls how much cold air enters the convertible drawer. If it is stuck in the open position or the actuator fails, cold air flows in continuously regardless of the temperature setting, causing the drawer to freeze.

  2. 02

    Faulty drawer thermistor

    Part replacement

    If the thermistor monitoring the convertible drawer is reading temperatures higher than actual, the control board will keep calling for more cooling. Checking the thermistor's resistance value against the expected specification will confirm or rule out this cause.

  3. 03

    Control board malfunction

    Part replacement

    The main control board manages the temperature zones throughout the refrigerator. If the board is sending incorrect signals to the damper or misreading the drawer's set point, it can cause overcooling even when the thermistor and damper hardware are functioning correctly.

  4. 04

    Incorrect drawer temperature setting

    Wiring / connection

    User error or a setting that was inadvertently changed can result in the drawer operating in freeze mode. Verify the drawer's temperature setting through the control panel before proceeding with component-level diagnostics.

  5. 05

    Wiring or connector issue

    Wiring / connection

    Damaged wiring or a loose connector between the thermistor, damper, and control board can cause erratic temperature control in the drawer zone. Inspect harness connections for corrosion, damage, or disconnection.

See the test procedure for each cause

Frequently asked questions about 0314

What does 0314 mean on a GE refrigerator?
Error code 0314 means the convertible drawer is reaching freezing temperatures while it is set to a warm temperature mode. The refrigerator's control system has detected that the drawer is not holding the selected temperature and is overcooling. This points to a problem with the damper, thermistor, or control board responsible for managing that drawer's temperature zone.
Can I fix error code 0314 myself?
Some causes of error 0314 are DIY-friendly, such as confirming the drawer setting is correct, inspecting wiring connections, and testing the thermistor resistance. However, replacing a damper assembly or control board typically requires disassembly of the refrigerator interior and comfort with basic electrical diagnostics. If you are not familiar with appliance repair, a qualified technician is recommended for those steps.
Is it safe to keep using my refrigerator while error 0314 is active?
The refrigerator's main compartment will generally continue operating normally while this fault is present, but food stored in the convertible drawer is at risk of freezing and spoiling. You should remove perishable items from the drawer until the issue is resolved to avoid food loss.
How much does it cost to repair error code 0314 on a GE refrigerator?
Repair costs vary depending on the failed component. A replacement thermistor is typically an inexpensive fix, often in the range of $20 to $60 for the part. A damper assembly or control board replacement can range from $80 to $300 or more for parts alone, with additional labor costs if a technician performs the repair.
Will resetting my GE refrigerator clear error code 0314?
A reset may temporarily clear the code from the display, but if the underlying hardware problem is still present, the fault will return once the refrigerator resumes normal operation. Resetting is useful for confirming whether the issue is intermittent, but it does not substitute for diagnosing and correcting the root cause of the overcooling condition.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass