mypros+
Error code reference

GE Refrigerator Error Code 0700

Stuck Keys on Temperature Control Board

GE codesGE refrigerator codes

Stuck Keys on Temperature Control Board

MyPros+ Max

Get the full diagnostic procedure for 0700.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0700 means on a GE refrigerator

Error code 0700 on a GE refrigerator indicates the main control board has detected one or more stuck keys on the dispenser control board. The dispenser board houses the touch pad or button inputs for water and ice dispensing functions. When a key registers as continuously pressed without being physically activated, the board flags the fault. This can result from a failed touch pad, a shorted membrane switch, liquid intrusion into the dispenser panel, or a defective dispenser control board itself.

For homeowners, this means the refrigerator's dispenser panel is sending a signal to the main board as if someone is holding down a button at all times. The refrigerator may still cool and freeze normally, but the dispenser functions for water and ice may behave erratically, stop responding, or become completely disabled while this code is active.

The dispenser board and its associated touch pad membrane are separate components from the main control board, so the problem is typically isolated to the front dispenser assembly. Inspecting the dispenser panel for moisture, physical damage, or warping is the logical first step before ordering replacement parts.

Source: manufacturer service documentation.

Common causes of 0700

  1. 01

    Failed dispenser touch pad membrane

    Part replacement

    The membrane switch layer beneath the dispenser buttons can degrade, tear, or short internally, causing one or more keys to register as permanently pressed. This is the most common trigger for code 0700.

  2. 02

    Moisture or liquid intrusion in dispenser panel

    Wiring / connection

    Water, ice melt, or spilled liquids can seep behind the dispenser panel and create a conductive bridge across key contacts, mimicking a stuck key. Drying out the panel may clear the code if no permanent damage occurred.

  3. 03

    Defective dispenser control board

    Part replacement

    The dispenser board itself can develop a fault in the key-sensing circuitry, reporting stuck keys even when the touch pad is functioning correctly. Replacing the dispenser board resolves this when the touch pad checks out.

  4. 04

    Damaged or pinched wiring harness between dispenser board and main control board

    Part replacement

    A wiring harness with chafed insulation or a loose connector can cause signal lines to short together, which the main board interprets as a stuck key condition on the dispenser board.

See the test procedure for each cause

Frequently asked questions about 0700

What does error code 0700 mean on a GE refrigerator?
Code 0700 means the main control board has detected a stuck key on the dispenser control board. One or more of the dispenser panel buttons is registering as continuously pressed. This is usually caused by a failed touch pad membrane, moisture behind the dispenser panel, or a faulty dispenser board.
How do I fix error code 0700 on a GE refrigerator?
Start by inspecting the dispenser panel for any visible moisture, cracks, or physical damage. Unplug the refrigerator for a few minutes and plug it back in to see if the code clears. If liquid got into the panel, allow it to dry completely and retest. If the code returns, the dispenser touch pad membrane or the dispenser control board will need to be replaced. Replacing the touch pad membrane is a manageable DIY repair on most GE models.
Can I still use my GE refrigerator when error code 0700 is active?
Yes, the refrigerator and freezer cooling functions typically continue to operate normally during a 0700 fault. The code is isolated to the dispenser board, so food safety is not at risk. However, water and ice dispensing may not work correctly or may be disabled until the fault is resolved.
How much does it cost to fix a GE refrigerator 0700 error code?
If the dispenser touch pad membrane is the culprit, the part typically costs between $30 and $80 depending on the model, and replacing it is a DIY-level repair requiring basic tools and about 30 to 60 minutes. A replacement dispenser control board ranges from $60 to $150 in parts. Adding professional labor brings the total repair cost to approximately $150 to $300. Getting the correct part number from your model label before ordering avoids costly returns.
Will unplugging my GE refrigerator reset error code 0700?
Unplugging the refrigerator for two to five minutes will clear the active fault display, but if the underlying stuck key condition still exists on the dispenser board, the 0700 code will return once power is restored. A reset is useful for confirming whether the fault is intermittent or persistent, which helps narrow down the cause.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass