mypros+
Error code reference

GE Refrigerator Error Code 0705

Key Pressed on Deli Pan Board while Door Closed

GE codesGE refrigerator codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 0705 error code actually means

Error code 0705 means your refrigerator's water dispenser control board ran into a problem while trying to automatically fill the water reservoir or complete a water delivery cycle. Essentially, the board expected the fill process to finish within a certain amount of time, but something went wrong and it could not complete the task. This could mean the dispenser is not getting water properly, or the board is having trouble communicating with the parts that control water flow.

Diagnostic procedure

The full 0705 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 0705 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 0705

Ranked by how often they cause this code
  1. 1Faulty or clogged water inlet valve
  2. 2Damaged or disconnected wiring harness to the dispenser board
  3. 3Failed dispenser control board
  4. 4Low or blocked household water supply

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 0705

What does error code 0705 mean on a GE refrigerator?
Code 0705 on a GE refrigerator means the dispenser board has detected an Auto Fill Error. This indicates the automatic fill cycle for the water dispenser or internal reservoir did not complete successfully. The cause can be a faulty water inlet valve, a wiring issue, low water pressure, or a failed dispenser board.
Can I still use my GE refrigerator with error code 0705 active?
The refrigerator's cooling functions will generally continue to operate with code 0705 active, so food storage is not immediately at risk. However, the water dispenser and any features dependent on the auto fill cycle may not work correctly. You should address the fault promptly to avoid water not reaching the ice maker or dispenser, which can cause secondary issues over time.
Will resetting my GE refrigerator clear error code 0705?
Unplugging the refrigerator for 30 seconds and restoring power will clear the stored code temporarily. However, if the underlying fault in the auto fill system is still present, code 0705 will return the next time the dispenser board attempts a fill cycle. A reset is useful for confirming whether the fault is intermittent, but it does not replace diagnosing and repairing the actual cause.
How do I fix error code 0705 on a GE refrigerator?
Start by checking that the household water supply valve behind the refrigerator is fully open and that the supply line is not kinked. Then inspect the water inlet valve for blockages or solenoid failure using a multimeter to test continuity. If the valve and supply line are intact, check the wiring harness connected to the dispenser board for damaged or loose connectors. If none of these resolve the code, the dispenser board likely needs replacement.
How much does it cost to fix a GE refrigerator showing code 0705?
If the fix is simply clearing a kinked supply line or opening a shut water valve, there is no parts cost. A replacement water inlet valve typically costs $30 to $80 in parts, and a new GE dispenser control board generally runs $75 to $150. Adding a technician's labor of $100 to $200 per service call, total repair costs can range from under $50 to around $350 depending on the failed component.

Related GE refrigerator error codes

All GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass