mypros+
Error code reference

GE Refrigerator Error Code 0706

Dispenser board auto fill error.

GE codesGE refrigerator codes

Dispenser board auto fill error.

MyPros+ Max

Get the full diagnostic procedure for 0706.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0706 means on a GE refrigerator

Error code 0706 on a GE refrigerator indicates a Dispenser Board Auto Fill Error. The dispenser control board has detected a fault in the automatic fill system, which governs the process of filling the ice maker, water reservoir, or both through the water fill valve and related circuitry. This typically occurs when the board sends a fill command and does not receive confirmation that the fill cycle completed correctly within the expected parameters, whether due to a signal failure, valve malfunction, or water supply issue.

For a homeowner, this means your refrigerator's control system tried to automatically fill a component with water and something went wrong in that process. You may notice the ice maker has stopped producing ice, the water dispenser is not working, or the refrigerator is displaying this code even though water appears to be getting through. The auto fill function is managed by the dispenser board, which acts as the communication hub between the water inlet valve, the ice maker, and the main control board.

This error can be intermittent or persistent depending on the root cause. A one-time occurrence can sometimes be cleared by resetting the refrigerator, but a recurring code points to a hardware problem in the water fill circuit that needs physical inspection and likely a component repair or replacement.

Source: manufacturer service documentation.

Common causes of 0706

  1. 01

    Failed water inlet valve

    Part replacement

    The water inlet valve controls water flow into the refrigerator. When it fails electrically or mechanically, the dispenser board cannot complete the auto fill cycle, triggering code 0706.

  2. 02

    Faulty dispenser control board

    Part replacement

    The dispenser board itself may have a defective relay or circuit that prevents it from properly commanding or confirming the auto fill sequence, causing a false or real error condition.

  3. 03

    Kinked, frozen, or restricted water supply line

    Wiring / connection

    If the water supply line leading to the refrigerator is kinked, frozen in the door or back panel, or has low household water pressure, the fill cycle will fail and the board will log error 0706.

  4. 04

    Wiring harness fault between dispenser board and water inlet valve

    Wiring / connection

    Damaged, corroded, or disconnected wiring between the dispenser board and the water inlet valve can interrupt the fill signal or feedback, causing the board to register an auto fill error.

See the test procedure for each cause

Frequently asked questions about 0706

What does error code 0706 mean on a GE refrigerator?
Error code 0706 means the dispenser board detected an Auto Fill Error. This means the refrigerator attempted to complete an automatic water fill cycle for the ice maker or water system and the process did not complete successfully. The root cause can be a faulty water inlet valve, a wiring issue, a restricted water line, or a problem with the dispenser board itself.
How do I fix error code 0706 on a GE refrigerator?
Start by resetting the refrigerator: unplug it for 60 seconds and plug it back in to see if the code clears. If it returns, check that your household water supply valve is fully open and the water line behind the refrigerator is not kinked or frozen. Next, test the water inlet valve for continuity using a multimeter. If the valve tests bad or you have verified water supply is fine and the error persists, replacing the water inlet valve is the most common fix. If the error continues after a valve replacement, the dispenser control board is the next component to evaluate.
Can I still use my GE refrigerator when error code 0706 is active?
The refrigerator will continue to cool food normally with code 0706 active, so your food is not at risk. However, the ice maker and water dispenser may not function correctly or at all while this error is present. You can continue using the refrigerator for food storage, but you should address the underlying cause soon to prevent the ice maker from running dry or the dispenser board from sustaining additional stress.
How much does it cost to fix a GE refrigerator with error code 0706?
If the fix is a water inlet valve, parts typically run between $30 and $80 depending on the model, and the repair is manageable for a confident DIYer since it involves disconnecting a water line and two to three wire connectors. A dispenser control board costs between $80 and $200 for parts. If you hire a technician, expect a service call fee of $80 to $150 plus labor and parts, putting the total repair between $150 and $400 depending on what component needs replacement.
Will unplugging my GE refrigerator reset error code 0706?
Unplugging the refrigerator for 60 seconds will clear the error code from the display, but if the underlying fault is still present the code will return once the refrigerator cycles through a fill attempt. A reset is a useful first step to confirm whether the error is intermittent or consistent, but it does not fix a failed water inlet valve, restricted water line, or faulty dispenser board.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass