mypros+
Error code reference

GE Refrigerator Error Code F141

Display board error.

GE codesGE refrigerator codes

Display board error.

MyPros+ Max

Get the full diagnostic procedure for F141.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F141 means on a GE refrigerator

The F141 error code on a GE refrigerator indicates a display board fault. The display board, also called the user interface board, is the electronic control panel that allows users to adjust temperature settings, activate features like the ice maker or water dispenser, and monitor the refrigerator's operating status. When the main control board detects a communication failure or internal fault within the display board, it triggers the F141 code to alert the user that this component is not functioning correctly.

The display board communicates with the main control board through a data line, and faults can arise from several sources. Loose or corroded wiring harness connectors between the two boards are a frequent culprit, as are power fluctuations that can cause the display board's onboard components to fail. Physical damage from moisture intrusion or mechanical impact can also compromise the board's circuitry.

Diagnosing this error typically involves inspecting the wiring harness connections at both the display board and the main control board for corrosion, damage, or loose pins. If the connections are secure and intact, the display board itself is likely defective and will need to be replaced. In some cases, the main control board may be sending incorrect signals, making it a secondary suspect if a new display board does not resolve the fault.

Source: manufacturer service documentation.

Common causes of F141

  1. 01

    Loose or Disconnected Wiring Harness

    Wiring / connection

    The ribbon cable or wire harness connecting the display board to the main control board can work loose over time. Inspect connectors at both ends for loose pins, corrosion, or visible damage.

  2. 02

    Failed Display Board

    Part replacement

    The display board itself may have failed due to a short circuit, moisture intrusion, or component burnout. If the board shows visible burn marks or the connectors are secure but the error persists, the board needs replacement.

  3. 03

    Corroded or Damaged Connectors

    Wiring / connection

    Moisture or age can cause corrosion on the wiring harness connectors, disrupting communication between the display board and the main control board. Check connectors for green or white oxidation and clean or replace as needed.

  4. 04

    Power Surge or Voltage Fluctuation

    Part replacement

    A sudden power surge can damage the display board's onboard components without leaving obvious visual signs. If the error appeared after a power outage or storm, the board may have been damaged by the event.

  5. 05

    Faulty Main Control Board

    Part replacement

    If a new display board does not clear the F141 error and all wiring checks out, the main control board may be sending faulty signals. This is a less common cause and should be considered only after other components are ruled out.

See the test procedure for each cause

Frequently asked questions about F141

What does F141 mean on a GE refrigerator?
The F141 code on a GE refrigerator indicates a display board error. It means the refrigerator's main control board has detected a fault with the user interface panel, which is the display you use to control settings. The cause can range from a loose wire connection to a fully failed display board.
Can I fix the F141 error myself?
Some DIYers can resolve F141 by checking and reseating the wiring harness connectors between the display board and the main control board. If the connectors look clean and secure but the error remains, replacing the display board is the next step, which is a moderate difficulty repair. If you are not comfortable working with appliance electronics, a licensed technician is recommended.
Will resetting my GE refrigerator clear the F141 error?
A reset, typically done by unplugging the refrigerator for a few minutes and plugging it back in, may temporarily clear the F141 code. However, if the display board or wiring connection is genuinely faulty, the error will return. A reset alone is not a fix, but it can help confirm whether the issue is intermittent or persistent.
Is the F141 error dangerous or a safety concern?
The F141 error is a display board fault and does not directly indicate a safety hazard such as a fire or refrigerant leak risk. However, if the display board is not functioning, you may lose the ability to monitor or adjust temperature settings, which could eventually affect food safety. It is best to address the error promptly to ensure the refrigerator operates correctly.
How much does it cost to fix a GE refrigerator F141 error?
Repair costs depend on the root cause. If only a wiring harness connection needs reseating, the cost may be limited to a service call fee, typically in the range of $75 to $150. Replacing the display board itself usually costs between $150 and $350 including parts and labor. If the main control board is also at fault, total costs could be higher.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass