mypros+
Error code reference

GE Refrigerator Error Code iD

IDUCT-sensor disconnection or short circuit.

GE codesGE refrigerator codes

IDUCT-sensor disconnection or short circuit.

First step from the service manual

Measure the resistance between both terminals after separating CN15 of the Main PCB. If disconnected or shorted, change the ID-sensor on the evaporator.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for iD.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What iD means on a GE refrigerator

The iD error code on a GE refrigerator indicates a fault with the IDUCT sensor, which monitors temperature within the refrigerator's air duct system. This sensor plays a role in regulating airflow and cooling performance by providing temperature feedback to the main control board. When the board detects that the sensor circuit is either open (disconnected) or shorted, it triggers the iD code to alert the technician that accurate temperature readings from that location are no longer available.

The primary diagnostic procedure involves separating connector CN15 from the main PCB and measuring the resistance across both sensor terminals. A proper reading should fall within the expected range for a functioning thermistor. If the measurement shows infinite resistance (open circuit) or near-zero resistance (short circuit), the ID sensor mounted on the evaporator is the confirmed fault point and requires replacement. This test isolates whether the fault lies in the sensor itself or in the wiring harness connecting it to the board.

Common triggers for this fault include physical damage to the sensor wiring, corrosion at the CN15 connector due to moisture exposure near the evaporator, or sensor failure from prolonged temperature stress. Because the sensor is located near the evaporator, ice buildup from a defrost system issue can also stress or damage sensor wiring over time. Resolving the iD code promptly is important because the control board cannot accurately manage cooling without reliable duct temperature data.

Source: manufacturer service documentation.

Common causes of iD

  1. 01

    Failed IDUCT sensor

    Part replacement

    The sensor itself has failed internally, resulting in an open or shorted circuit. This is confirmed by measuring resistance at the CN15 connector terminals after disconnecting the harness from the main PCB.

  2. 02

    Disconnected sensor wiring

    Wiring / connection

    The wiring harness between the IDUCT sensor and connector CN15 on the main PCB may have come loose or been pulled free, resulting in an open circuit reading. Inspect the full length of the wiring from the evaporator to the board.

  3. 03

    Corroded or damaged CN15 connector

    Wiring / connection

    Moisture near the evaporator can cause corrosion at the CN15 connector pins, creating high resistance or an intermittent open circuit. Inspect the connector for green or white oxidation and damaged pins.

  4. 04

    Wiring harness short or chafing

    Part replacement

    The sensor wiring may be pinched against a metal edge or damaged by ice buildup, causing the two conductors to contact each other and create a short circuit. Look for worn insulation or areas where the harness contacts the evaporator housing.

  5. 05

    Ice damage from defrost system failure

    Part replacement

    If the defrost system has been malfunctioning, excessive ice accumulation near the evaporator can physically stress or crush sensor wiring over time. Addressing a defrost failure may be necessary alongside sensor replacement.

See the test procedure for each cause

Frequently asked questions about iD

What does iD mean on a GE refrigerator?
The iD code indicates a disconnection or short circuit in the IDUCT sensor, which is a temperature sensor located near the evaporator. The main control board monitors this sensor through connector CN15 and triggers the code when it detects an open or shorted circuit. Without a valid signal from this sensor, the refrigerator cannot accurately regulate its internal temperature.
Can I fix the iD error code myself?
A knowledgeable DIYer can start by inspecting the wiring harness and the CN15 connector on the main PCB for obvious damage or disconnection. Confirming the fault requires a multimeter to measure resistance across the sensor terminals after unplugging CN15. If the sensor tests open or shorted, replacing the IDUCT sensor on the evaporator is required and involves working near refrigerant lines, so comfort with appliance repair is important before proceeding.
Is it safe to keep using my refrigerator while the iD code is showing?
Operating the refrigerator with an active iD code means the control board is working without accurate duct temperature data, which can affect cooling performance and efficiency. Food safety may be at risk if the unit is not maintaining proper temperatures. It is best to address the fault promptly rather than continue using the refrigerator in this condition.
Will resetting the refrigerator clear the iD error code?
A power reset may temporarily clear the code from the display, but the error will return if the underlying sensor fault has not been repaired. The iD code is triggered by a measured electrical fault, either an open or shorted circuit, so the condition must be corrected physically before the code will stay cleared.
How much does it cost to repair the iD error code on a GE refrigerator?
If only the IDUCT sensor needs replacement, parts costs are typically in the range of $20 to $60 depending on the specific model. If a service technician is needed for diagnosis and replacement, total repair costs including labor generally range from $100 to $250. Additional costs may apply if wiring harness damage or a defrost system fault is also found during inspection.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass