mypros+
Error code reference

GE Refrigerator Error Code P

Pass result displayed during diagnostic communication check or sensor test indicating component or…

GE codesGE refrigerator codes

Pass result displayed during diagnostic communication check or sensor test indicating component or communication is functioning correctly.

MyPros+ Max

Get the full diagnostic procedure for P.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What P means on a GE refrigerator

The P code on a GE refrigerator is a pass result, not a fault. It appears during the refrigerator's built-in diagnostic routine when the control board runs a communication check or sensor test and confirms that a specific component or communication pathway is functioning correctly. This code is part of GE's self-test sequence, where the board cycles through individual systems and reports either a pass or fail for each one. Seeing P means the component under evaluation responded within expected parameters.

For homeowners, P is a green light from your refrigerator's diagnostic system. When you or a technician run the diagnostic mode, the control board tests sensors and communication lines one by one. A P result means the component being checked at that moment passed its test, which is the expected and desired outcome. You are not looking at a problem code.

No repair action is needed when P is displayed during diagnostics. If you entered diagnostic mode intentionally to investigate a separate concern, continue cycling through the test sequence to look for any actual fault codes. If P is the only result you are seeing, the system checked out clean for that component.

Source: manufacturer service documentation.

Common causes of P

  1. 01

    Intentional diagnostic mode entry

    Wiring / connection

    A technician or homeowner manually initiated the refrigerator's diagnostic or service mode to test components. P is the normal, expected output when a sensor or communication circuit passes its test.

  2. 02

    Successful communication check on a previously flagged component

    Wiring / connection

    After a prior fault was cleared or a component was repaired, the diagnostic routine re-ran a communication check and confirmed the fix resolved the issue. P confirms the component is now communicating correctly with the control board.

  3. 03

    Sensor within normal resistance or signal range

    Wiring / connection

    During a sensor-specific test, the control board read a voltage or resistance value within the acceptable range for that sensor. This triggers a P result, indicating the sensor is operating as designed.

See the test procedure for each cause

Frequently asked questions about P

What does the P code mean on a GE refrigerator?
P stands for Pass. It appears during GE refrigerator diagnostic mode and indicates that the component or communication circuit being tested at that moment is functioning correctly. It is not an error or fault code. No repair is needed when you see P.
Is my GE refrigerator safe to use when it shows P?
Yes. P is a pass result from the diagnostic system, meaning the tested component checked out as healthy. Your refrigerator is operating normally. If you entered diagnostic mode to investigate another issue and P is the only code that appeared, the system found no fault in the tested circuit.
How do I exit diagnostic mode after seeing P on my GE refrigerator?
To exit the diagnostic or service mode on most GE refrigerators, press and hold the same button combination used to enter the mode, or simply unplug the refrigerator for 30 seconds and plug it back in. Refer to your specific model's service sheet, which is usually found taped inside the refrigerator compartment, for the exact exit procedure.
Why does my GE refrigerator keep showing P?
If P is cycling through repeatedly, the refrigerator is likely still running its full diagnostic sequence and displaying a pass result for each component it tests. This is normal behavior during the self-test routine. Once the sequence completes, the display should return to normal operation or show any actual fault codes that need attention.
How much does it cost to fix the P code on a GE refrigerator?
There is no repair cost associated with a P code because it indicates a passing result, not a failure. If you are seeing P, the component under diagnostic test is working correctly. If you have a separate underlying concern that prompted you to run diagnostics, the cost of repair depends on any fault codes that appear alongside or after the P result during the full diagnostic cycle.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass