mypros+
Error code reference

GE Washer Error Code 9

Lid Switch Redundancy

GE codesGE washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 9 error code actually means

Your GE washer noticed that, in three cycles in a row, it thought the lid was open even after the cycle finished, and it's now refusing to start a fourth time until this is addressed. This is a safety feature designed to make sure the lid switch system is working correctly before running again. Try lifting and firmly closing the lid to reset the error and see if the washer resumes normal operation.

Diagnostic procedure

The full 9 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Open and close the lid to clear the error.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 9 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 9

Ranked by how often they cause this code
  1. 1Lid Not Fully Closing or Latching
  2. 2Worn or Faulty Lid Switch Assembly
  3. 3Loose or Damaged Wiring Harness
  4. 4Misaligned Lid Strike
  5. 5Control Board or Backup Processor Fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 9

What does 9 mean on a GE washer?
Error code 9 on a GE washer is a lid switch redundancy fault. It means the backup microprocessor detected the lid as open at the end of three consecutive cycles, and a fourth cycle start was attempted before the issue was resolved. The washer triggers this lockout as a safety measure to ensure the lid switch system is functioning correctly before allowing further operation.
Will resetting the washer clear error code 9?
The specified reset method for this code is to open and close the lid rather than a power cycle. This action signals to the control system that the lid switch condition has been addressed. If the error returns after this reset, the underlying lid switch or wiring issue needs to be repaired, as simply resetting without fixing the root cause will result in the code reappearing.
How much does it cost to repair error code 9 on a GE washer?
If the fix is simply realigning the lid strike or cleaning the switch area, there may be no parts cost at all. A replacement lid switch assembly typically runs in the range of $15 to $50 for the part, with labor adding $75 to $150 if a technician is called. A control board replacement, needed only in rare cases, can range from $150 to $350 or more for the part alone.
How do I fix error code 9 on my GE washer?
Start by opening and then firmly closing the lid to reset the error. If the code clears and the washer runs normally, check that the lid closes completely and that the lid strike is properly aligned with the switch. If the error returns after multiple cycles, inspect the lid switch assembly and the wiring harness connecting it to the control board, as one of these components is likely failing.
Is it safe to use my GE washer when error code 9 is showing?
Error code 9 is a safety lockout, and the washer will not start a new cycle while the fault is active. This is intentional, as the lid switch system ensures the lid is closed during spinning. Do not attempt to bypass the lid switch to force the washer to run, as this removes a key safety protection against contact with moving parts.

Related GE washer error codes

All GE washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass