mypros+
Model reference

Fisher & Paykel 680

Refrigerator

5 documents72 error codes23 service modes

Available documentation

Service Manual

  • 600 Series Electronic Control System27 pg
    Covers this model
  • 600 Series Technical Service/Training Manual Addendum144 pg
    Covers this model

Bulletin

  • Refrigeration Bumpons1 pg
    Covers this model
  • Refrigeration Service Bulletin2 pg
    Covers this model

Service Flash

  • Summary Of Changes To "G" Series Refrigerators and Service Procedures For These Changes9 pg
    Covers this model
MyPros+ Max

Diagnose your Fisher & Paykel 680.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (72)

CodeMeaning
01EAcknowledgement signal for water level not received within time allowed.02EDoor status acknowledgement signal not received during program operation.03EDoor lock acknowledgement signal not received within time allowed.05Refrigerator cabinet thermistor read open or shorted for 10+ seconds, or…06Refrigerator evaporator thermistor read open or shorted for 10+ seconds, or…06EWater level signal above parameter set, on program start-up.07Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly…07EWater level signal above parameter set for safety, during program.08No heating detected during wash program operation.1Lock Monitor10Mode Shift Feedback Monitor10EWater level signal is above parameter set (10 scale units) after water…11Clock Monitor11EMechanical unbalance always activated.12Redundant Flood Condition12EThe program control unit cannot read the program EPROM.13Redundant Lid Unlocked13EThe program control unit receives no response from the motor control unit.14Water Temp Sensor Invalid14EWater level system not calibrated.15Lid Lock Failure16Adaptive Drain / Slow Drain17Dry Load Sense Timeout17EDoor status acknowledgement signal not received, although door lock…18Drain Pump Clearing algorithm failed18EOnly with CALCAD 440019UI State Timeout19ECommunications between the CALCAD 4400 and the program control unit board…2Lid Monitor20Critical Flood Level by Gallons
View all 72 error codes
20EMotor control unit has not received signal for lock acknowledgement, during…21Water Accessibility21EThe electronic timer wrongly configured.22Options Knobs Feedback Invalid22EThe automatic calibration system for water level is not working.23Suds Lock Abatement Failure24Stuck Button Fault25Max Fill26Out of Balance (OOB) during Dry Load Sense27Critical Lid Lock Failure28Lid Logic Failure29Pressure Sensor Dropout3Locked Rotor Monitor30Out of Balance (OOB) Ended Final Spin31Out of Balance (OOB) Fallback In Final Spin31ETemperature of motor control unit heat sink too high.32Critical Lid Lock Failure32EThermal protection for motor has cut out.33EThe motor control unit has received a start command from the program control…35EMotor control unit indicating short-circuit between motor winding outputs.36EMotor control unit indicating fault/error in receiving circuitry for lock…37EMotor control unit indicating DC voltage level too low.38EMotor control unit indicating DC voltage level too high.4Reset Monitor41EThe motor controller indicates an error in thermal protection circuits of the…43EThe RDC card indicates the unbalance switch has triggered when motor is stopped.45EThe RDC card indicates tacho pulses missing.5Mode Shifter6Critical Flood Level by pressure7Max Fill8Pressure Sensor Loss9Lid Switch RedundancyEC 05Refrigerator cabinet thermistor read open or shorted for 10+ seconds, or…EC 06Refrigerator evaporator thermistor read open or shorted for 10+ seconds, or…EC 07Freezer cabinet thermistor read open or shorted for 10+ seconds, or repeatedly…EC 08Freezer evaporator thermistor read open or shorted for 10+ seconds, or…EC 20Defrost under-heat with no voltage feedback through gray/white wire at defrost…EC 21Defrost overheat.EC 22No voltage feedback through gray/white wire at defrost start.EC 23Defrost overheat with no voltage feedback through gray/white wire at defrost…EC 24Defrost under-heat.EEThermistor is open or shorted, or there is a break in the thermistor's wiring…

Service modes (23)

  • Consumer Error Mode (CEM)From an idle state only (all LEDs off), press and hold Start button for 10 seconds
  • diagnostic["Unit must be ON.","Press and hold either COLDER key.","Then press the UNIT ON/OFF key.","Release…
  • Diagnostic ModeWith the unit ON, press and hold either COLDER key, then press the UNIT ON/OFF key, then release…
  • Field Service ModePress and hold Start button while rotating the cycle selection knob 180 degrees (7 clicks) and then…
  • Manual Compartment Disable ModeSwitch the unit OFF using the UNIT ON/OFF key
  • Manual Component Activation ModeWith the unit ON, press and hold the desired compartment COLDER key and the UNIT ON/OFF key for 10…
  • Manual Freezer Evaporator DefrostPress and hold the ICE key for 5 seconds, then release.
  • Manual Mode (no program running)["From main menu, press down arrow to highlight 'OPTIONS MENU'.","Press SELECT.","In the MENU…
  • manual_compartment_disable["Switch unit OFF using the UNIT ON/OFF key.","With unit switched OFF, press and hold the WARMER…
  • manual_component_activation["Unit must be ON.","Press and hold the desired compartment COLDER key and the UNIT ON/OFF key for…
  • manual_freezer_evaporator_defrost["Press and hold the ICE key for five seconds, then release."]
  • Sabbath ModeSwitch the unit OFF using the UNIT ON/OFF key
  • sabbath_mode["Switch unit OFF using the UNIT ON/OFF key.","With unit switched OFF, press and hold the UNIT…
  • Service Mode["From main menu, press down arrow to highlight 'OPTIONS MENU'.","Press SELECT.","Navigate to MENU…
  • Service program (coin meter configuration)["Press the service button.","Certain buttons switch to number keys (0 to 9).","Enter service codes…
  • Showroom ModeSwitch the unit OFF using the UNIT ON/OFF key
  • showroom_mode["Switch unit OFF using the UNIT ON/OFF key.","With unit switched OFF, press and hold either pair…
  • Temperature Log Recall Mode (Compartment and Evaporator)With the unit ON and in Diagnostic Mode, toggle to the desired thermistor temperature reading
  • Temperature Log Recall Mode (Compartment Only)With the unit ON, press and hold the desired compartment WARMER key, then press the UNIT ON/OFF…
  • Temperature Units Selection ModeWithin the first minute after switching the unit ON, press and hold the Door Ajar Alarm Bell key…
  • temperature_log_recall_compartment_and_evaporator["Begin with the unit ON and in Diagnostic Mode.","Toggle through readings until the desired…
  • temperature_log_recall_compartment_only["Begin with the unit ON.","Press and hold the desired compartment WARMER key.","Then press the…
  • temperature_units_selection["Must be performed within the first minute after switching the unit ON.","Press and hold the door…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel refrigerator models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax