mypros+
Error code reference

GE Washer Error Code Control Board Failure (Lid Lock Circuit)

The main control detects that the motor controller is not activating the lid lock circuit.

GE codesGE washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Control Board Failure (Lid Lock Circuit) error code actually means

Your GE washer has detected a problem with the electronic control that manages the lid lock, which is the safety feature that keeps the lid closed during a wash cycle. The washer's main computer board is not getting the signal it needs to confirm the lid is properly locked, so the machine has stopped to prevent unsafe operation. A technician will most likely need to replace the main control board to fix this issue.

Diagnostic procedure

The full Control Board Failure (Lid Lock Circuit) procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace the main control board.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Control Board Failure (Lid Lock Circuit) procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Control Board Failure (Lid Lock Circuit)

Ranked by how often they cause this code
  1. 1Failed Main Control Board
  2. 2Failed Motor Controller
  3. 3Wiring Harness Fault Between Boards
  4. 4Lid Lock Actuator Failure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Control Board Failure (Lid Lock Circuit)

What does Control Board Failure (Lid Lock Circuit) mean on a GE washer?
This error means the main control board has detected that the motor controller is not properly activating the lid lock circuit. The lid lock is a safety component that must engage before the washer can spin or agitate. When the control board cannot confirm the lid lock circuit is functioning, it stops operation and displays this fault. The main control board is the first component flagged for replacement.
Is it safe to use my GE washer when this error is showing?
No, you should not attempt to continue using the washer while this error is active. The lid lock circuit is a primary safety system designed to prevent the lid from opening during high-speed spin cycles. If the control system cannot confirm the lid is properly locked, operating the machine poses a safety risk. The washer should remain out of service until the fault is diagnosed and repaired.
Will resetting my GE washer clear the Control Board Failure (Lid Lock Circuit) error?
A power reset, such as unplugging the washer for a few minutes and plugging it back in, may temporarily clear the error code. However, if the underlying fault in the main control board or motor controller circuit is still present, the error will return once the washer attempts to lock the lid again. A reset is not a repair and should only be used as a quick diagnostic step to check whether the fault is intermittent. Persistent return of the code confirms a hardware failure that requires part replacement.
Can I fix the Control Board Failure (Lid Lock Circuit) error myself?
Replacing a main control board is within the skill range of an experienced DIYer who is comfortable working with appliance electronics and handling live voltage precautions. Before replacing the board, it is worth checking the wiring harness connections between the main control and motor controller for any loose or corroded pins. If connections are secure and the error persists, the main control board will need to be replaced. Sourcing the correct replacement board for your specific GE model number is essential.
How much does it cost to repair a Control Board Failure (Lid Lock Circuit) error on a GE washer?
If the main control board is the cause, parts costs typically range from $100 to $300 depending on the specific GE model. Adding professional labor, total repair costs can range from $200 to $450 or more. If the motor controller also requires replacement, costs will be higher. Getting a diagnostic visit from a certified technician can help confirm which components actually need replacing before committing to parts purchases.

Related GE washer error codes

All GE washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass