Model reference

GE GTUP270GMWW

Washer

12 documents20 error codes3 service modes

Available documentation

Service Manual

  • GEWasherLaundryCenterGTUP240270ServiceManual31920869 pg
    Covers this model
  • 24" & 27" Unitized Laundry Centers101 pg
    Covers this model
  • 24" & 27" Unitized Laundry Centers101 pg
    Covers this model
  • 24- and 27-in. Unitized Laundry Centers Technical Service Guide69 pg
    Covers this model
  • GE Appliances Technical Service Guide - 24- and 27-in. Unitized Laundry Centers69 pg
    Covers this model
  • Technical Service Guide - 24- and 27-in. Unitized Laundry Centers69 pg
    Covers this model
  • 31-9208-24-27-inch-unitized69 pg
    Covers this model
  • 24" & 27" Unitized Laundry Centers101 pg
    Covers this model

Service Flash

  • Laundry Centers Lid Issues3 pg
    Covers this model

Tech Tip

  • GE Washer Dryer GTUP270 GTUP240 Laundry Centers Lid Issues TAG TIP2 pg
    Covers this model

Other

  • GTUP270 TP102 pg
    Covers this model
  • HL06 131 pg
    Covers this model
MyPros+ Max

Diagnose your GE GTUP270GMWW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (20)

CodeMeaning
Blocked MotorControl does not receive pulses from the motor Hall sensor, indicating the…Control Board Failure (Lid Lock Circuit)The main control detects that the motor controller is not activating the lid…Control Board Failure (Low Water Agitate)The washer tries to agitate with less than the minimum allowed water level…Control Board Failure (Min Water Level)Washer attempts to agitate with less than the minimum allowed water level…Control Board Failure (Motor Triacs)The triacs that control the motor windings have failed.Fill Time OutFill timeout occurred; non-critical error displayed to consumer.Filling TimeoutControl does not receive a change of pressure from the pressure switch within 3…Lid Lock BrokenCritical failureLid Lock FailureCritical failureLid Lock Not Open/CloseLid cannot be locked or unlocked; control attempts 5 times, then waits 4.25…Lid SwitchControl runs 3 continuous agitation/spin cycles without receiving the lid…Lid Switch FailureCritical failureLoose BeltControl detects excessive motor speed from the Hall sensor, indicating a loose…No SpeedNo motor speed sensor feedback detected; after 3 seconds without feedback in…OverflowWater level detected higher than the expected maximum fill; water valves are…Pump TimeoutDrain pump timeout reached after 4.25 minutes of pumping without reaching…Redundancy FeedbackMain control detects that the motor controller is not activating the lid lock…ThermistorControl cannot detect the ATC thermistor; ATC is disabled and defaults to…Triac in ShortThe triacs that control the motor windings have failed.Wash TransistorWasher tries to agitate with less than the minimum allowed water level…

Service modes (3)

  • Clear Error Codes["1
  • Field Service Mode["Press and hold the START and FABRIC SOFTENER buttons simultaneously.","While holding both…
  • Washer Service Mode["1

Full entry steps, exit procedures, and test sequences are available in Max.

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax