mypros+
Error code reference

GE Washer Error Code E35

Pressure sensor indicates excess water (better models).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E35 error code actually means

Your GE washer detected too much water inside the drum and stopped to prevent a potential overflow. This could mean water kept flowing in when it should have stopped, or a sensor that monitors water level is giving an incorrect reading. Either way, the machine needs attention before it will run normally again.

Diagnostic procedure

The full E35 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if water level is above 4.5 inches (refer to Test 6).
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E35 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E35

Ranked by how often they cause this code
  1. 1Faulty water inlet valve
  2. 2Defective pressure sensor
  3. 3Clogged or kinked pressure hose
  4. 4Waterlogged air dome
  5. 5Control board communication fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E35

What does E35 mean on a GE washer?
E35 means the pressure sensor has detected that the water level inside the washer tub has exceeded the acceptable limit, typically above 4.5 inches. The machine stops operation to prevent an overflow situation. This code appears on better model GE washers equipped with advanced pressure sensing. The cause can be either a genuine overfill from a faulty inlet valve or a false reading from a bad sensor or blocked pressure hose.
Is it safe to keep using my GE washer when E35 is showing?
It is not advisable to continue running the washer while E35 is active. The code indicates a potential overfill condition, which means water could overflow the tub and cause water damage to your home or the machine's electrical components. The washer halts operation as a protective measure, and that protection should be respected until the underlying cause is diagnosed and corrected.
Will resetting my GE washer clear the E35 error code?
A reset may temporarily clear the E35 code, but if the underlying problem, such as a faulty inlet valve or defective pressure sensor, is still present, the code will return during the next wash cycle. Resetting without repairing the cause is not a permanent solution and leaves the risk of an actual overflow unresolved. Proper diagnosis of the water level and pressure sensing system is necessary before the error will stay cleared.
How do I fix the E35 error on my GE washer?
Start by opening the lid and checking the actual water level inside the tub. If water is visibly high, the water inlet valve is likely faulty and should be replaced. If the water level appears normal, inspect the pressure hose for kinks or blockages and test the pressure sensor using the Test 6 diagnostic procedure. Clearing any hose obstruction or replacing the defective sensor or inlet valve will typically resolve the error.
How much does it cost to repair an E35 error on a GE washer?
Repair costs depend on the faulty component. A water inlet valve replacement typically ranges from $80 to $200 including parts and labor. A pressure sensor replacement generally runs between $60 and $150. If the issue is simply a kinked or clogged pressure hose requiring no parts, a service call fee of $75 to $125 may be the only expense.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass