mypros+
Error code reference

GE Washer Error Code FLOOD

Flooded condition detected, pump out exceeded 3 minutes.

GE codesGE washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the FLOOD error code actually means

Your GE washer detected too much water inside the tub and tried to pump it out, but the draining process took longer than 3 minutes without fixing the problem. This could mean water is still coming in from the supply valves when it should not be, or the drain system is not working fast enough to remove the water. The machine stopped the cycle automatically to prevent a potential overflow or flood on your floor.

Diagnostic procedure

The full FLOOD procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check water valves and pressure switch.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock FLOOD procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of FLOOD

Ranked by how often they cause this code
  1. 1Faulty water inlet valve
  2. 2Defective or stuck pressure switch
  3. 3Clogged drain pump filter or drain hose restriction
  4. 4Drain pump motor failure
  5. 5Excessive detergent causing foam

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about FLOOD

What does FLOOD mean on a GE washer?
The FLOOD code means the washer detected an excess water condition and attempted to pump the water out, but the pump-out cycle ran for more than 3 minutes without resolving the problem. The machine stops the cycle automatically to prevent overflow. The most common causes are a water inlet valve that will not close fully or a faulty pressure switch.
Will resetting my GE washer clear the FLOOD error code?
A reset may temporarily clear the FLOOD code and allow the machine to restart, but if the underlying problem is not fixed, the code will return during the next wash cycle. Resetting without diagnosing the root cause is not a long-term solution. Address the water inlet valve, pressure switch, and drain system before attempting to run a load again.
How much does it cost to repair a GE washer showing the FLOOD error?
Repair costs vary depending on the failed component. A replacement water inlet valve typically runs between $30 and $80 for the part, while a new pressure switch generally costs between $20 and $60. Drain pump replacements tend to fall in the $40 to $120 range for parts. Adding professional labor, total repair costs can range from $100 to $300 or more depending on the diagnosis.
How do I fix the FLOOD error on my GE washer?
Start by checking the water inlet valves to confirm they are fully closing when the machine is not filling. Then inspect the pressure switch and its air hose for kinks, cracks, or blockages. Also clean the drain pump filter and check the drain hose for restrictions. If the inlet valve is allowing water to seep in continuously, it will need to be replaced.
Is it safe to use my GE washer when the FLOOD code is showing?
No, you should not continue using the washer while this code is active. The FLOOD error indicates the machine cannot properly control or remove water, which means there is a real risk of water overflowing onto your floor. Leave the washer unpowered until the cause of the error has been identified and corrected.

Related GE washer error codes

All GE washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass