mypros+
Error code reference

Hotpoint Washer Error Code E14

Machine failed to heat the water within the allowed time.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E14 error code actually means

Your Hotpoint washer tried to heat the water for your wash cycle but could not get it warm enough in the time allowed. This usually means a heating part inside the machine has failed, such as the heating element or a temperature sensor. A technician will need to test those components to find out which one needs to be replaced.

Diagnostic procedure

The full E14 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check heater, thermistor, wiring connections, power module.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E14 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E14

Ranked by how often they cause this code
  1. 1Failed heating element
  2. 2Faulty thermistor
  3. 3Damaged or corroded wiring connections
  4. 4Power module failure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E14

What does E14 mean on a Hotpoint washer?
E14 means the washer failed to heat the water to the required temperature within the allowed time during a wash cycle. The fault points to a problem in the heating circuit, which includes the heating element, the thermistor, the wiring connections, and the power module. The washer will typically stop the cycle and display this code to alert you that the heating system needs attention.
Is it safe to use my Hotpoint washer when E14 is showing?
Running the machine with an active E14 code means your clothes will not be washed at the intended temperature, so hygiene and wash quality will be compromised. There is also a risk of the underlying fault causing further electrical issues if a wiring or component failure is involved. It is advisable to stop using the machine until the fault is diagnosed and repaired.
Will resetting my Hotpoint washer clear the E14 error?
Performing a reset, such as unplugging the machine for a few minutes and restarting it, may temporarily clear the E14 code. However, if the underlying component, such as the heater or thermistor, has actually failed, the error will return as soon as the machine attempts to heat water again. A reset is useful for ruling out a one-time control glitch, but it is not a substitute for properly diagnosing and repairing the fault.
Can I fix E14 on my Hotpoint washer myself?
Some steps, such as inspecting and reseating wiring connectors, are within reach for a confident DIYer with basic tools. Testing the heating element and thermistor with a multimeter requires some technical knowledge but is manageable with proper guidance. Replacing the power module or heating element involves working near high-voltage components, so if you are not comfortable with electrical safety procedures, it is best to call a qualified technician.
How much does it cost to repair a Hotpoint washer E14 error?
Repair costs vary depending on which component has failed. A replacement thermistor is generally a lower-cost part, typically in the range of $15 to $40, while a new heating element can run from $30 to $80 for the part alone. If the power module has failed, parts and labor combined could bring the total to $150 or more. Adding a technician call-out fee will increase overall costs.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass