mypros+
Error code reference

Jenn-Air Range Error Code F3-1

Open or shorted oven temperature sensor.

Jenn-Air codesJenn-Air range codes

Open or shorted oven temperature sensor.

First step from the service manual

Ohm sensor and harness.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F3-1.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F3-1 means on a Jenn-Air range

The F3-1 error code on a Jenn-Air range indicates a fault in the oven temperature sensor circuit. Specifically, the control board has detected that the sensor is either open (broken circuit with infinite resistance) or shorted (circuit collapsed to near-zero resistance). The oven temperature sensor, sometimes called an RTD (resistance temperature detector), is a probe mounted inside the oven cavity that changes its electrical resistance in a predictable way as temperature rises and falls. The control board reads this resistance to determine oven temperature and regulate the bake and broil elements accordingly. When the resistance falls outside the expected range, the board throws F3-1 and typically disables the oven to prevent overheating or inaccurate cooking temperatures.

The diagnostic process starts with ohming out both the sensor itself and the wire harness that connects it to the control board. A functioning oven temperature sensor on most Jenn-Air ranges reads approximately 1080 to 1090 ohms at room temperature. A reading of zero or near-zero ohms indicates a short within the sensor or harness, while an open line (OL or infinite reading on a multimeter) points to a broken wire, failed sensor, or disconnected connector. The harness should be inspected along its entire run from the sensor probe at the back of the oven cavity through the rear panel to the control board connector, looking for pinched wires, heat damage, or corrosion at the terminals.

Source: manufacturer service documentation.

Common causes of F3-1

  1. 01

    Failed oven temperature sensor

    Part replacement

    The sensor probe itself has burned out or degraded, causing its resistance to read as open or shorted. Confirm by disconnecting the sensor and checking its resistance with a multimeter at the two terminals on the probe connector.

  2. 02

    Damaged or broken wire harness

    Part replacement

    The wiring between the sensor and the control board can crack, burn, or break, especially where it passes through the oven rear panel. Inspect the full harness run for visible damage and test continuity on each wire.

  3. 03

    Loose or corroded connector

    Wiring / connection

    The connector at the sensor end or at the control board can work loose or develop corrosion, interrupting the circuit. Disconnect each connector, inspect the pins for oxidation or bent contacts, and reseat firmly.

  4. 04

    Shorted harness from contact with oven cavity

    Part replacement

    If the sensor harness contacts the hot metal of the oven cavity or a burner component, insulation can melt and cause a short to ground. Look for areas where the harness runs close to heating elements or sharp metal edges.

  5. 05

    Faulty control board

    Part replacement

    If the sensor and harness both test within spec but the error persists, the control board itself may have a failed input circuit for the sensor. This is the least common cause and should only be considered after the sensor and wiring are confirmed good.

See the test procedure for each cause

Frequently asked questions about F3-1

What does F3-1 mean on a Jenn-Air range?
F3-1 indicates that the oven temperature sensor circuit is either open or shorted. The control board cannot read a valid resistance signal from the sensor probe inside the oven cavity. This fault typically disables oven heating to protect against uncontrolled temperatures. The first diagnostic step is to ohm out the sensor and its wiring harness.
Can I fix the F3-1 error myself?
A knowledgeable DIYer can diagnose the issue by using a multimeter to check the resistance of the sensor at its connector, looking for approximately 1080 to 1090 ohms at room temperature. If the sensor reads open or shorted, replacing it is a straightforward repair involving disconnecting the probe from inside the oven and unplugging the harness connector. Harness repairs require more skill and care working near the control board.
Is it safe to use my Jenn-Air range when F3-1 is displayed?
You should not use the oven while this fault is active. Without a reliable temperature signal, the control board cannot regulate heat properly, which could result in overheating or underheating. Surface burners on a gas or electric cooktop may still function, but the oven should remain off until the sensor circuit is repaired.
Will resetting the range clear the F3-1 error code?
Resetting the range by cycling the breaker or unplugging it may temporarily clear the display, but the code will return as soon as the oven tries to operate and reads the faulty sensor circuit again. A reset does not fix the underlying electrical fault in the sensor or wiring. A proper repair or part replacement is necessary to resolve the code permanently.
How much does it cost to repair a Jenn-Air range F3-1 error?
If the oven temperature sensor is the cause, the part itself typically costs between $20 and $75 depending on the specific model, making it one of the more affordable oven repairs. If professional labor is involved, total repair costs including the part and service call generally range from $100 to $250. A damaged harness or failed control board will push costs higher, with control boards ranging from $150 to $400 or more for the part alone.

Related Jenn-Air range codes

All Jenn-Air range codes
View all 73 Jenn-Air range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass