mypros+
Error code reference

Jenn-Air Range Error Code 1d11

Unlocked runaway temperature condition detected (temperature exceeds 600°F with latch not locked).

Jenn-Air codesJenn-Air range codes

Unlocked runaway temperature condition detected (temperature exceeds 600°F with latch not locked).

MyPros+ Max

Get the full diagnostic procedure for 1d11.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 1d11 means on a Jenn-Air range

Error code 1d11 on a Jenn-Air range indicates that the oven cavity temperature has exceeded 600 degrees Fahrenheit while the door latch remains in the unlocked position. This condition is flagged as a "runaway" temperature event because the oven is reaching temperatures that are normally only appropriate during a self-clean cycle, yet the door latch has not engaged to confirm a controlled cleaning sequence is underway. The control board monitors both the oven temperature sensor (RTD probe) and the latch switch status simultaneously, and when these two signals conflict, the 1d11 fault is triggered as a safety measure.

The most common root cause is a malfunctioning oven temperature sensor or a faulty control board that is misreading sensor data and allowing the heating element to continue energizing beyond normal cooking limits. A failed latch assembly or a latch switch that is not reporting its position accurately to the control board can also produce this fault, since the board may see an unlocked state even when the latch has physically moved. In some cases, a runaway heating element caused by a failed relay on the control board can drive oven temperatures above 600 degrees independently of any user-initiated cycle.

Because this fault involves abnormally high oven temperatures in an unlocked state, the range should not be operated until the underlying cause is diagnosed and corrected. Technicians should inspect the RTD sensor resistance at ambient temperature (typically near 1080 ohms at room temperature for standard probes), verify the latch motor and switch operation, and evaluate the control board for relay failures or erratic output signals.

Source: manufacturer service documentation.

Common causes of 1d11

  1. 01

    Faulty oven temperature sensor (RTD probe)

    Part replacement

    A failing RTD sensor can send incorrect resistance readings to the control board, causing the board to misread the oven temperature or allow heating to continue unchecked. Check the sensor resistance at room temperature and compare it to the specified value for your model.

  2. 02

    Control board relay failure

    Part replacement

    A stuck or shorted relay on the electronic control board can keep the bake or broil element energized continuously, driving oven temperatures above safe limits regardless of the set temperature. This typically requires replacing the control board.

  3. 03

    Latch switch malfunction

    Part replacement

    If the latch switch fails to correctly report the latch position to the control board, the board may interpret the door as unlocked even during high-heat operation, triggering the 1d11 fault. Test the latch switch for continuity through its range of motion.

  4. 04

    Latch motor assembly failure

    Part replacement

    A failed latch motor may prevent the door latch from fully engaging, leaving the latch in an unlocked position during high-temperature conditions. Inspect the latch motor for proper movement and listen for the motor attempting to actuate.

  5. 05

    Corrupted or failed control board programming

    Part replacement

    In some cases, a software or hardware fault in the control board can cause it to misinterpret sensor and latch data, generating a false 1d11 code. If all sensors and the latch assembly test correctly, the control board itself may need replacement.

See the test procedure for each cause

Frequently asked questions about 1d11

What does 1d11 mean on a Jenn-Air range?
The 1d11 code means the oven detected a temperature above 600 degrees Fahrenheit while the door latch was not in the locked position. This is considered a runaway temperature condition because such high heat should only occur during a self-clean cycle with the door securely latched. The range shuts down and displays this code as a safety precaution. The oven should not be used again until the fault is diagnosed and repaired.
Is it safe to use my Jenn-Air range while it shows error code 1d11?
No, you should not operate the range while this code is active. The 1d11 fault indicates the oven reached dangerously high temperatures in an unlocked state, which presents a fire and safety risk. Disconnect power to the range and keep it off until a qualified technician has inspected and repaired the cause of the fault.
Will resetting my Jenn-Air range clear the 1d11 error code?
A power reset by unplugging the range or shutting off the circuit breaker for a few minutes may clear the code temporarily, but it will almost certainly return if the underlying component failure is not addressed. The fault is tied to an actual hardware condition, either a sensor, latch, or control board problem, and resetting alone does not fix those components. A reset can be useful to confirm whether the code is intermittent, but repair is still required.
How do I fix a 1d11 error code on a Jenn-Air range?
Fixing this code requires identifying which component is responsible for the runaway temperature condition or the incorrect latch status signal. Common repair steps include testing the RTD temperature sensor for correct resistance, inspecting and testing the door latch motor and switch, and evaluating the control board for relay failures or erratic behavior. Because multiple components can cause this fault, a systematic diagnostic approach is recommended before replacing parts.
How much does it cost to repair a Jenn-Air range with error code 1d11?
Repair costs vary depending on which component has failed. A replacement oven temperature sensor typically ranges from $30 to $80 for the part, while a latch assembly can run $50 to $150. A control board replacement is usually the most expensive repair, with parts often ranging from $150 to $400 or more depending on the model. Adding professional labor costs of $100 to $200 or more is typical if you are not performing the repair yourself.

Related Jenn-Air range codes

All Jenn-Air range codes
View all 73 Jenn-Air range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass